I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi
I need to read the Drive mode of how an output pin has been configured....
I see that there is an API to read pin's Pullup, Direction, Sense, etc configuration.....
Hi,
I want to make an emitter and a receiver for AOA. I have seen that the example i have to use is " Direction_finding_connectionless_tx (and rx)" but when i open it on...
Hi,
I'm using two UARTs on nRF52840 with SDK17.1.
My issue is both UART works individually until they receive messages at the same time. Both of them receive an RX overrun...
Hello,
NCS1.9.1, VSCode, peripheral_lbs
nRF5340-DK got error:
undefined reference to `z_impl_k_busy_wait'
nRF21540-DK and nRF51840-DK work well.
Best re...
Hi,
I was measuring the time it takes to boot to my application based on the nRF52832 and the time I measured was excessively long.
I'm using a PicoScope DSO for observing...
Hi,
I've been requested a feature regarding buttonless OTA DFU that I'm not sure if it's feasible or advisable to implement.
The feature is that once the OTA is successful...
Hi,
I do not know how to reliably get size of arbitrary UDP data received by #XRECV or #XRECVFROM.
It is clear for text data, but for binary data both #XRECV and #XRECVFROM...
Hi everyone,
I have a preblem for BLE Mesh 5.0 version (board is nrf52840),
I found that in the Setting set function of the Sensor Model, it seems that the data is transmitted...
Hi, I am using Zephyr and want to use the nrfx_timer_compare functions. It seems that the system is working with Timer4 and channel 0 to 4. However, the compare of channel...
Hello,
I have many board of nrf9e5 IC's,
But in nordic company it's discontinue,
It had long range and easy to set,
Now which product is like this?
I need part number...
Hello,
I am using the nRF52840 DK (same applies also for the dongle). The setup is quite simple. I have two nodes on my desk, one transmitting packets and the other receiving...
Hi
I have combined the ble_app_uart and libuarte example. The combination works "nearly" well.Transmit is ok, but when receiving characters over UARTE, no NRF_LIBUARTE_ASYNC_EVT_RX_DATA...
I see a square hollowed out area in the middle of the newly released questions about nrf5340 audio DK PCBA. What is the design purpose of this hole hollowed out area?
