Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
I tryed to reduce the power consumption of my beacon (ble_app_beacone example from SDK) to have more battery live. To do this, I want to reduce the TX power. And also change...
I have to initialize a i2c multiplexer, for that I am sending the device address and register address to be written using the function:
nrf_drv_twi_tx(&m_twi, (0x70), tx_buf...
Hi,
I'm currently using nRF Connect SDK v1.9.0 and developing on a nRF52832 onto a custom board. I'm using a BMI090L from Bosch connected over i2c.
I'm trying to suspend...
Hi.
Encountering an intermittent issue where, after a DFU (either OTA using Nordic Device Manager or over usb serial using dfu-util on Linux), the image is reportedly in...
I have vsc version 1.66. I'm getting the following notification:
File changes watcher stopped unexpectedly. A reload of the window may enable the watcher again unless...
In the DTS file for I2C, how do you set the port of the pin specified?
&i2c0 { compatible = "nordic,nrf-twi"; status = "okay"; sda-pin = <26>; scl-pin = <27>; };
In...
Hi,
I have a question about the whitelist，when we use the function "pm_whitelist_set()" to set the whitelist，whether the whitelist is stored in RAM or FLASH? I traced the...
Hello,
I am using nrf52810 with custom board and i have created DFU for uploading a OTA file previously its working fine but i don't know what happens now BLE is getting...
Hi:
When i read data from the device nrf52833 to android app, only get 600byte data and it should be 4096byte. The app use the Android-BLE-Library-2.4.0 lib.
The nrf52833...
Hi,
I have a question on SDK release plans. There is a change awaiting for release (merged after 1.9.1) and it would be nice to develop them with an official release, including...
Hello!
We are two students working on IO-Link Wireless as a bachelor thesis project. Our task is to make a Wireless Master prototype using the nrf52840 DK kit from nordic...
I am making a ble beacon application. I need to send more than 30 bytes of data via advertisement. How can I do? Because UUID data will not be enough for me.
Hello everyone and hello kindly nRF support team!!
One question again sry. I am using SDK 1.9.1 through VS Code and working on the nRF Connect SDK Tutorial - Part 2 -...
