Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
we have a zephyr application on nRF52832 DK with nRF Connect for vscode
Before we added DFU support, we had a power consumption of 28 uA
After adding DFU support...
3 months ago Nordic stated the following
The S140 version 6.0.0 SoftDevice does not have full support for S=2 (500 kbps). The application cannot select S=2, so all packets...
Hi Nordic guys,
I'm developing with nrf5340, and meet some problem with writing external flash - nrf qspi flash.
I found it sometime failed in 'flash_area_write' and return...
Hi,
I'm using SDK17.02 on nRF52810, when my application have an error, it will log "fatal error" but never reset system. BTW, I'm not debugging and just watching the RTT...
Hi
I want to update the ble advertising data in my program. In nrf5340 the bt_le_adv_start() command should run only once in the main program.
Is it possible to change...
I 'm developing a program (C# ) on PC for the nRF52840 dongle (pca10059) that is a RSSI scanner.
Scanning different BLE channels in the environment. The program is much...
Hi Sir,
We plan to test the WebUSB example under the below path:
/ncs/1.8.0/zephyr/samples/subsys/usb/webusb HW: nRF52840-DK When we compile, program and connect to the...
I bumped into some compilation errors regarding PRS box4, when I tried to remove UART from an example.
I saw that PRS is "Peripheral Resource Sharing", but it looks like...
I am working on nRF Connect SDK 3,9.3 version. One day a dailog to update appeared. I clicked to update while SES was also opened and I was working on a project. Suddenly...
Hi,
I am working on a firmware and have added custom services to HRS example on SDK 17. I want to know if its possible to add BLE multiperipheral capability to my device...
I don't have enough pins to dedicate a SPI bus to the nRF21540.
In the webinar I attended I believe I heard that the SPI bus is not supported by the current SDK anyway,...
Hello everyone,
This was discussed before, elsewhere ( link) , however, it is meant for the "nRF51422 chip " and I need to resolve some other points too ...
it is necessary...
Hi,
I am working on the sample DFU OTA project as recommended below,
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu?CommentId=3cb5df69...
I am developing an applicaiton to run on the app core of an nRF5340, and I have mcuboot enabled for the purposes of handling DFU.
I have recently implemented signing the...
