Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
We are using nRF52840 on a custom board with nRF5 SDK v15.3.0.
Our application uses the NFCT driver (nrfx_nfct) along with nfc_t2t_lib_gcc.a to emulate a NFC tag with some...
HI,Therd:
I used the mesh sdk 5.0.0(BLE SDK 17.0.2), and run the example light_switch_server_nrf52832_xxAA_s132_7_2_0.emProject. when i use the nRF Mesh app on the phone...
Hi,
I am evaluating nRF53 for ZigBee in a Linux application that implements a MQTT-SN Gateway. I am interested in learning about Linux board can connect to the nRF53 (USB...
using nRF5 SDK 17.1.0
Segger
I need some understanding of the QDEC. if I connect a motor that has a A/B output at a 5KHZ rate.
what is the maximum rate at which the...
Hi!
What is the easiest way to compare two sdk_config files? Some tools, etc. Why do I need it:
My idea is to use "$NRF_SDK/config/nrf52840/config/sdk_config.h" as base...
Hi,
We are trying to change the name of our BLE device of our solution with being always different for each device. The device name would be like a serial number that is...
SDK: 7.0.2
CHIP: nRF52840
I'm faced with strange dfu behavior.
The dfu SD+BL+APP (softdevice 6.1.1 -> 7.2.0) is working fine which was flashed by j-link.
However...
Hi,my project is going on with nrf5340dk,i use the codec tlv320aic3109 to record audio data.i have the linux driver about this IC，but i haven't familar linux driver.could...
Hi,
I am trying to utilize the nRF Thread Topology Monitor with the CLI example from nRF Connect SDK, but it does not seem to work. " Error - No response from Thread CLI...
Hi,
Want to know more about NV memory interface
Do we have implementation in Nordic SDK for to keep the data stored into the memory
Please share the code path if we...
Hi,
Yesterday I received the nRF5340-DK. I started following the 'Get started' procedure on the product page. The LEDs start pulsating and pressing the buttons lights up...
Hi,
I have some issue in developing APP for devices based on NRF51822. They have been developed in 2016 with an old bootloader, when there was no use of zip pack. We usually...
My project uses nRF52832 and I'm at the point of the project where I'm trying to minimize power consumption.
To assist in this, I created a very small main() that goes through...
Dear Support,
I have tried to find the correct info to integrate the DFU functionality of the nRFConnect app on the phone into our own mobile app. We want to be able to...
I am trying to read data from a sensor through I2C which follows below particular sequence attached.
The 1st piece in this sequence is to wakeup the sensor and ends...
