Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
HI,
I recently migrated my nrf52840 based devices to Thread and Zigbee SDK 4.2.0
I used to have a good power consumption around 100-150uA with zigbee enabled.
Since...
I'm considering using the NRF52840 for a device with infrared proximity sensors that requires 8 IR LEDs to be driven at around 14 mA successively (never more than one at a...
Hi Nordic community
We have a custom IC to interface with the nRF52840 chip. We did testing for that IC with FPGA and the related control, clock signals are as shown in...
Hi guys,
We designed a custom board with the nRF52840 SoC and is trying to use the QSPI interface to communicate with an external flash AS5F18G04SND-10LIN.
We are having...
Can someone point me to where I can find some information about the secure vs non-secure builds and what considerations are required for either? Currently I'm trying to create...
Hello,
What is the difference between 2 devices which are constantly scanning and 2 devices which are connected? Also, how do I code 2 devices to connect to each other?...
Hello,
I am going off a fresh install of nrf connect desktop and installed the 2.0.0 version of the toolchain from the toolchain manager. When i create new project from...
Dear all
I am looking for a tutorial like this https://devzone.nordicsemi.com/guides/short-range-guides/b/bluetooth-low-energy/posts/ble-central-tutorial
It sounds quite...
Hi,
The manual for nRF5340 DK states: "VDD can be set by the nRF5340 firmware". I need to set the VDD to 1.8V. How is this done? I can't find any code documentation on...
I am running Version 1.9.1 of the NRF SDK, am programming in VScode, and have written my own custom board and associated DTS files for the hardware we are implementing.
...
Hello,
We are working toward certification of our product and conducting TRP/TIS measurements. The TRP and TIS are not matching up with the conducted output power and...
I'm having a hard time developing for Nordic Hardware right now as it seems that the hardware is not recognized by VSCode/NrfConnect anymore. Under the Connected Devices Section...
Dear,
I use an nrf5340 dk with sdk 1.8.0 for vscode. I'm now playing with the central_and_peripheral_hr example and I want to change the advertisement packet. How and where...
Hi,
I have an issue in regard to Matter. I would like to commision a device in my network, but I don't know why the Python CHIP Controller returns this error every time...
