Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
Hello, I'm in the process of attempting to implement Eddystone EID on the nRF52805.
It's been a bit of a nightmare, so I'm finally taking the bold step to make my first...
I am using SDK 17.1.0 with an nRF52832 design similar to the P10040.
I was previously using the original timer application and things were looking good. I decided to upgrade...
Hi,
1. Please provide me with an example in which UART0, UART1, uart2, and uART3 are enabled
2. The sending and receiving rate of each UART must reach 1,000,000 baud rate...
We are porting a project from SDK 11 to nrf5 SDK 17.0.2. We have also used a couple of different versions of SDK 15 extensively on several different products.
Our code...
SDK: NCS 2.0.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF5340
IDE: VS Code
Hi Everyone,
I am porting an existing project based...
Hello All,
We are intending to start a new project using nRF52840 SOC, for the same i decided to work with nRF connect SDK as it is recommended by nordic,
I am new to...
When connecting to AWS IOT the Asset Tracker V2 uses MQTT to AWS-IOT. This is TLS 1.2 from what I understand. We are using the 1.8 skd / 1.3.1 modem firmware.
We have...
Hi everyone
We have developed a smartwatch with a nrf9160 chip. We have used nrf Connect SDK 1.2 for the development process.
Now we want to migrate our project to nrf...
Hello there,
I am using the peripheral/radio/transmitter and receiver example in SDK17
But I am only able to transmit 2 bytes. I want to transmit like 8 or 9 bytes...
Hi,
I am testing FOTA function using sample "http_update/application_update" on NRF9160DK.
But found that the system boot stuck at
I had tested this sample with...
HI
I am using this sequence functions in my main loop for low current consumption
__SEV(); __WFE(); __WFE();
normally I have 13mA in my application when I am using...
nrf5-sdk v16.0.0
If you use the nrf_ble_scan module to try and connect to a peripheral that emits both connectable and non-connectable advertising packets, the module does...
Hello !
From PS it is not always clear what RADIO registers/fields are relevant for Ieee802154_250Kbit radio mode and must be initialized.
For example CRCINC ?
On "Figure...
Hi team,
I'm making BT low power keyboard using nRF52832 DV kit and with Zephyr RTOS. For this which IDE is best OR comfortable?
But I'm not getting example code if anyone...
I am programming an external device with the same code loaded onto the nRF5 DK. The sample works on the DK, It broadcasts and I can connect. However, when I program an external...
