Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
My board works most of the time are very good，but one time i power down the board when ble connecting and data transmitting，the board can't work when power on.and i can't...
Posting this as separate question as it got no traction in the other thread:
Why are there many of the same include files in the DFU example directory as in the S110 7...
Hi all,
this is not a question per se but rather a warning to those who are attempting to debug Flash related operations with the SEGGER J-Link GDB Server (v4.84a for Linux...
I debugging some function abnormal after OTA problem, and problem with disappear after redo OTA FW upgrade, duirng it I found a problem about Master Control Panel FW upgrade...
I would like to make my own project of an analog sensor with BLE feature. Is it a good idea to go with third party module (because of the easy availability of Antenna)? can...
Hi! I measure the micro frequency by Hantek Osiloskop in two-mode.
First, I use a simple Blink without softdevice , reaching 570kHz in 10us. Second, I use a ble_app_blinky...
Hi, I am looking for some help in interfacing STM32F4 MCU and nRF52832 module via UART for establishing BLE communication. My application needs both the devices.
I downloaded...
Hello everyone,
how can I implement a blacklist for my central which is scanning for a UUID and should also check for example device name. If the device name is in the blacklist...
We have developed a sensor application using ESB protocol with the nRF SDK (nRF52832 on Tx side and nRF52840 on Rx side).
We would like to redevelop now the receiver under...
Hi
1、I made the following modifications to the hello_world example（ncs1.7.0\v1.7.0\zephyr\samples\hello_world.
2、I have disabled uart0,But the average power...
Hi,
I'd want to implement RTC for regular testing of a variable. I am largely based on The BLE_uart exemple and have added a timer instance and a PWM instance. As the...
Hello,
I run a piece of code on NCS1.8.0 on nRF5340-DK, and it returns -35 when executing k_msgq_get()，b ut the same code runs on NCS1.5.0 and the k_msgq_get() function...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
Since I want to bond with Android, I have created a central code that summarizes the functions that I...
Hello everyone i am trying to integrate nRF Calendar example with the nRF5 Thread MQTTSN example. In my application, I will get the date and time source from the MQTT-SN JSON...
Hello,
I have a zephyr project built using NCS v1.8.0 with target board selected as nRF9160DK_nrf9160_ns. I am interfacing LSM6DSO sensor with nRF9160 dk, with interrupt...
Hello,
We have a firmware developed for Full Thread Device. But now as i want to reduce power consumption i want to convert FTD device firmware to SED firmware.
SDK...
After reading this https://devzone.nordicsemi.com/f/nordic-q-a/3830/what-is-the-value-of-the-gpio-pull-up-and-pull-down-resistor
and seeing that the internal pull-up is...
I'm trying to get readings from an LPS22HB sensor with the nrf52810 using the lps22hb driver in SDK 17.0.2_d674dde.
The lps22hb_init() call completes without any errors...
Hi, I'm using nRF52805 and SEGGER.
The firmware could be programmed to the chip successfully when I use Debug->go. I can connect with the BLE signal.
However, when I use...
