hi, i am using a cutom board based on nrf5340 mcu , so, while setting it up i am facing the problem in checking logs and led status.
i am uisng the nrf5340dk board to build...
Hi Nordic technical expert，
Can random numbers in broadcast intervals be cancelled or fixed? How to modify the software? Could there be other problems if random number times...
I added ring buffer and UART ASYNCH interface to asset_tracke_v2. I added CONFIG_RING_BUFFER = y, CONFIG_SERIAL = y and CONFIG_UART_ASYC_API = y to prj.conf file. The build...
Hi,
I am looking at setting up some of our team with the ability to flash our custom devices that contain various chips (nrf52, nrf53, nrf91). Assuming the SEGGER software...
Hello,
I have run the GATT throughput example to test the throughput for a long range. My test configuration is as below:
ATT MTU: 247
Data length: 27
Connection...
Team,
I am using nrf52810, sdk 17, sd112.
I have setup a write characteristics, to receive some long data ( 64 bytes)
// write char memset(&add_char_params, 0, sizeof...
Hello,
I have a BLE peripheral device that becomes the server once a connection is established. The BLE services and characteristics are all custom, I will include the defines...
I have a product with an nRF9160 and using its modem to connect to a LWM2M server. I have recently enabled modem delta firmware updates, and have seen an annoying issue. The...
Hi,
We want to explore I2C examples in nCS SDK 1.7.1
Can you please enlist all the examples having I2C implementation.
also want to add I'm referring to I2C API's...
Hello everyone!
I am using my nrf9160dk to develop a system that connects to Azure IoT Hub. My firmware code is based on provided azure_iot_hub sample. According to azure_iot_hub...
I 'm using BLE Nordic UART Service (NUS) for streaming data packets which contains read sensor data. I need a way to check the packet loss happening for example if the other...
Hello,
I am developing an application that requires advertising of multiple custom service over BLE. I have successfully implemented the custom services, assigning a custom...
Hi All,
As far as I know , BLE Thrughput is basically set around a few parameters => 1. NRF_SDH_BLE_GAP_DATA_LENGTH
2. NRF_SDH_BLE_GATT_MAX_MTU_SIZE
3. NRF_SDH_BLE_GAP_EVENT_LENGTH...
1) I have set up the Zephyr development environment by following the instructions at https://docs.zephyrproject.org/latest/getting_started/index.html
2) I am able to build...
In my device， I must support HUB(central and peripheral roles) mode. I found it will drop data in weak signal. and It will be better when be central roles only in the same...
Hello.
I am just do one project with Zephyr and nrf52840 to control one step motor, the one task is to get pulse number of pwm pulse when motor is running , I think PPI...
Hello guys,
I'm trying to interface nrf52832 with ds18b20 temperature sensor and I'm using this code https://github.com/sigurdnev/Nordic-DS18B20 and I'm getting the output...
I start a application from the demo central-uart with the NRF CONNECT SDK 1.9.1
I try to communication via the com.
but the first byte of the rx buffer is wrong,I did...
I am running the throughput sample project on sdk 1.9.0 using two nRF5340 dev kits and am getting a throughput of 197 kbps using 2M PHY, Data Length 251 and Interval of 7...
Since upgrading to SDK 17.1.0 i get the following warnings of a redundant redeclaration for SystemCoreClock, SystemInit() and SystemCoreClockUpdate() for nrf52810 and nrf52840...
Hi,
I've installed the nRF Connect SDK, and want to bring up a command-line build environment.
I'm able to do it as it says in the instructions here : Bring up the Toolchain...
How to upgrade the nRF52832 tag in OpenWRT+nRF52832 gateway
gateway(openwrt+nrf52832) |_____ nrf52832 tag1 |_____ nrf52832 tag2 |_____ nrf52832 tag3 |_____ nrf52832 tag4...
