hi, i am using a cutom board based on nrf5340 mcu , so, while setting it up i am facing the problem in checking logs and led status.
i am uisng the nrf5340dk board to build...
Hi Nordic technical expert，
Can random numbers in broadcast intervals be cancelled or fixed? How to modify the software? Could there be other problems if random number times...
I added ring buffer and UART ASYNCH interface to asset_tracke_v2. I added CONFIG_RING_BUFFER = y, CONFIG_SERIAL = y and CONFIG_UART_ASYC_API = y to prj.conf file. The build...
Hi,
I am looking at setting up some of our team with the ability to flash our custom devices that contain various chips (nrf52, nrf53, nrf91). Assuming the SEGGER software...
Hello,
I have run the GATT throughput example to test the throughput for a long range. My test configuration is as below:
ATT MTU: 247
Data length: 27
Connection...
Team,
I am using nrf52810, sdk 17, sd112.
I have setup a write characteristics, to receive some long data ( 64 bytes)
// write char memset(&add_char_params, 0, sizeof...
Hello,
I have a BLE peripheral device that becomes the server once a connection is established. The BLE services and characteristics are all custom, I will include the defines...
Hi,
I discovered that when I use the 'write' button in the nrf connect programmer, that it completely overwrites the whole program (similar to erase&write). Before I didnt...
I am developing a proof of concept for a device however I have some questions regarding the Zephyr display libraries, I have a wave share display with no driver such as SSD16XX...
Hi, Is there a limitation on the available MCLK frequency for the NRF9160 I am trying to configure I2S master with 16K sampling, 16bit, and after i2s_configure() SDK info...
Hi,
I am now working on communication part between esp32 and nrf5340. I want to send the data via ble from nrf5340 and it will receive by esp32. Now, I can able to connect...
Hi sir
We're now working with the nrf52840 DK board, and we want to use two i2c at the same time, but I'm having trouble with one i2c working properly, which means twi1...
Dear Sir.
I use these commands to connect the Modem ON and OFF.
I need to know if the result of the these commands the Modem communicates with the Cell tower ?
Please...
Hi,
I have nrf52833-DK. Where should I get started for DOA applications? I'm experienced with other nRF chips, but not for DF and RTL applications specifically.
Hi team,
I would like to stream(through USB) data every 10millisecond using RTC interrupt.
is this possible or should i use other timers for this purpose ?
Can i configure...
Hello,
I try to debug a BLE connection with the nRF Sniffer. As a test, I used one nRF52 DK (PCA10040) as peripheral using nRF Connect and and Android phone as central device...
I'm using the HID keyboard as the base example. We're using prototype hardware so the connection gets dropped periodically due to ongoing hardware issues. But this has exposed...
Hi, nordic Engineer!
Merry Christmas！ I am using the DF to develop my project and considering simulation with the Bluetooth signal with antennas to build a customized antenna...
Hi,
I am trying to receive messages via Bluetooth mesh and forward them via UART (using UART async API) on the nrf9160DK. But when I try this, I get an assertion error from...
Hi,
I'm using SDK17.2 to develop nRF52810's application.
When APP_ERROR_CHECK or APP_ERROR_HANDLER have a fault which is caused by hardware or software, the system will...
Hi,
I want to trigger a wake up from System ON sleep (WFE) using the LDETECT signal on Zephyr.
I managed to wake up using Zephyr's gpio API but my understanding is that...
1. Nrf52840 acts as central and Nrf52832 acts as peripheral. when nrf52840 has connected with nrf52832, nrf52832 disconnected occasionally. Disconnect reason 0x0013. When...
