Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi! I am in the process of trying to install the Asset Tracker on my Thingy91. I have got it to work with nrfCloud and I am now trying to configure it to use the AWS backend...
I am using the nRF52 SDK : nRF5_SDK_17.0.2_d674dde
- When data are all ASCII-Hex (0x30) the code working fine
- Now I try to optimize code by changing to binary data....
I have been using the nRF52-DK for while and it been good.
But when I accidental hold the "BOOT/RESET" button, the board now stop working. only LEDs is blinking (per sec...
I would like to ask if someone from India ever used Thingy:91? Which SIM card is used or where to get the supported SIM card? How to get it working in India?
In VS Code, when pushing the " Connect To RTT In nRF Terminal " button, a message shows up:
J-Link V7.20 Device Selection The selected device "NRF52832_XXAA_REV2" is unknown...
Goodday all
Im trying to drive some Neopixel LEDs with 52840DK SDK_17.1.0. and have been following this example. https://devzone.nordicsemi.com/f/nordic-q-a/70560/nrfx_i2s...
I'm trying to install and run the nRF Command Line Tools, but am running into issues. I was able to successfully install the Linux32 version of the tools, but when I go to...
Hi
I am using nrf52840 and I want to use nrf_calendar example with app_ble_uart,
I am traying to send parameter from nrf toolbox uart app mobile
but I have no idea how...
Hi,
I am using nordic 52840 development kit along with sdk17.1
I am tried to use ble-uart example code to receive data from the app and based on the data i need to write...
I'm trying to follow the instructions to perform an OTA DFU for the Thingy 52.
https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/dfu_generating.html...
I'm using SDK 1.7.0. Here's how I have the modem code setup.
Init modem outside of thread loop
Set modem at+ comman CFUN=1 (start searching for a tower)
Once +CEREG...
hi,
when I call 'mesh_stack_device_reset()' function from the application, then the bootloader goes into infinite loop.
exactly at the point int the main() -> init_clock...
We are supplying the nRF52840 from 5 V into the VDDH pin. We are not using the USB interface, so I want to confirm what our options are for the VBUS pin. Can we leave it floating...
