Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi,
I discovered that when I use the 'write' button in the nrf connect programmer, that it completely overwrites the whole program (similar to erase&write). Before I didnt...
I am developing a proof of concept for a device however I have some questions regarding the Zephyr display libraries, I have a wave share display with no driver such as SSD16XX...
Hi, Is there a limitation on the available MCLK frequency for the NRF9160 I am trying to configure I2S master with 16K sampling, 16bit, and after i2s_configure() SDK info...
Hi,
I am now working on communication part between esp32 and nrf5340. I want to send the data via ble from nrf5340 and it will receive by esp32. Now, I can able to connect...
Hi sir
We're now working with the nrf52840 DK board, and we want to use two i2c at the same time, but I'm having trouble with one i2c working properly, which means twi1...
Dear Sir.
I use these commands to connect the Modem ON and OFF.
I need to know if the result of the these commands the Modem communicates with the Cell tower ?
Please...
Hi,
I have nrf52833-DK. Where should I get started for DOA applications? I'm experienced with other nRF chips, but not for DF and RTL applications specifically.
Hi team,
I would like to stream(through USB) data every 10millisecond using RTC interrupt.
is this possible or should i use other timers for this purpose ?
Can i configure...
Hello,
I try to debug a BLE connection with the nRF Sniffer. As a test, I used one nRF52 DK (PCA10040) as peripheral using nRF Connect and and Android phone as central device...
I'm using the HID keyboard as the base example. We're using prototype hardware so the connection gets dropped periodically due to ongoing hardware issues. But this has exposed...
Hi, nordic Engineer!
Merry Christmas！ I am using the DF to develop my project and considering simulation with the Bluetooth signal with antennas to build a customized antenna...
Hi,
I am trying to receive messages via Bluetooth mesh and forward them via UART (using UART async API) on the nrf9160DK. But when I try this, I get an assertion error from...
Hi,
I'm using SDK17.2 to develop nRF52810's application.
When APP_ERROR_CHECK or APP_ERROR_HANDLER have a fault which is caused by hardware or software, the system will...
Hi,
I want to trigger a wake up from System ON sleep (WFE) using the LDETECT signal on Zephyr.
I managed to wake up using Zephyr's gpio API but my understanding is that...
1. Nrf52840 acts as central and Nrf52832 acts as peripheral. when nrf52840 has connected with nrf52832, nrf52832 disconnected occasionally. Disconnect reason 0x0013. When...
