Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I need to configure an nRF52832 to wake up periodically from SYSTEM_ON and SYSTEM_OFF and, also, when a GPIO pin changes.
Where can I find sample code and docs for...
Hi Nordic experts,
i figure out how to add the end-point-out to the BLE HID EXAMPLE and i cheched it out on linux ubuntu and on windows 10.
It seems to work correctly...
For my Thingy91 project I need to hook into a variety of hardware interfaces including I2C. I am struggling to relate the pins https://infocenter.nordicsemi.com/topic/ug_thingy91...
Hello,
I'm using the nRF Connect SDK 1.9.1 and I have defined a custom board with nRF52840. This works for normal code (samples, etc).
The .dst has the following structure...
Hi,
Im using PCA10056 nrf52840 to measure light intensity with photodetector.
I got that sensor to measure the intensity of the light on the Arduino. But I don't know...
Hi all,
I have a problem when I try to debug nRF52832 target. The nRF52832 chip is advertising properly but as soon as I enter in debug mode, advertising stops. There is...
We got a project that is using custom boards and custom libraries that is able to compile for one board and that output strange errors for an other. Following is the prj.conf...
Summary: Not able to see messages from printf() statements in the code on the serial monitor.
I'm new to Nordic platform and to Segger Embedded Studio.
I have a Nordic...
Hello,
could you please tell me how to configure the Hardware Chip Select Funtionality for SPIM3. I am developing a communication between a sensor and the NRF via SPI transfers...
Hello everyone,
I am currently using NRF5340dk and I need the Library queue, (I especially need the functions: nrf_queue_push and nrf_queue_pop..). (Knowing also that I...
Hi Nordic Team, I am trying to develop an AOA application using the NRF52833 nordic SOC. I am using NCS 1.6.1 development SDK in Segger Embedded Studio.
I am flashing a...
Hi
I want to measure the battery lithium, this battery is the principal source (3.7v 300mh), the maximum voltage is 4.2 when the charge is full,
i'm using this code for...
Hi
I'm trying to enable BLE host-only build on Application core on nrf5340dk, and also enable RPMsg/openAMP.
I'm using Zephyr and its build system.
I get the following...
Hello everyone,
I'm working on a project right now and I want to use the ADS1298 analog to digital converter and configure it with NRF5340dk. Being a beginner I looked for...
hello,
i'm having an nrf52 based system with an antenna switcher in front of it, for antenna diversity. i tried using BT_HCI_OP_READ_RSSI as basis for my antenna diversity...
