Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Is there any zigbee example for nrf52840 dongle (PCA10059) ? If not, what is additional changes needed to add support in existing examples?
I unable to run the zigbee switch...
Hi, I need to add Azure IOT connectivity to nRF5340DK. I have already tested NodeMCU based data upload to HTTP based server and successfully working. Now, to divert the data...
I am trying to upgrade SoftDevice and Application firmware from v6.1.1 to v7.2.0 on Nordic USB840M dongle and I am facing a strange issue after such upgrade.
Please find...
Hi,
I have created my own service and charecteristic
1. But i am seeing only unknown service - How to give a name to this service
2. I am getting unknown charecteristic...
Hi
I have compiled (successfully) the Zephyr example samples/bluetooth/peripheral example for the nRF52 DK (nRF52832).
I am going through the code and trying to understand...
Hi
I have developed a device using the nRF52832 and I am wondering if there is built in functionality to reset the chip back into bootloader mode without programming the...
Hi All,
I'm using SDK17.1.0 and I have a question about mobile device subscribe.
I asked this question before, but the engineer didn't reply, so I asked again, thank...
Hi All,
I want to port BPS to my custom project, I encountered the problem as the title.
When I connect and trigger the subscribe like this picture.
My project will...
I have code that runs for around 5 days, then for some unknown reason hangs or stops running, which makes it almost impossible to debug.
I have also tried to implement interrupt...
Hi.
I have an issue that, If I power off Master and do save flash at Slave side together, the nrf_fstorage_is_busy(p_fs) return value always true .
When BLE is connectting...
I added a mesh shell module to my firmware running on nRF52480 .
Opened the mesh shell
uart:~$ mesh init Mesh shell initialized
mesh provision 0 0x100 0
Crash (see...
I've been slowly adding NVS functionality to my code. Has been working fine, up until today when I attempted to write a struct I have for storing historical data to flash...
Hey,
I have implemented BT FOTA process for my zephyr based application. DFU over Bluetooth works fine. But now I struggle to implement manual upload of image (it will be...
Hello Devzone,
My name is Ted. Recently I posted here and received some good help on low power sample code for the nRF9160DK board. This code helped me prove in real life...
I'm currently trying to set up a simple demo using 2 dev kits running the SPIS and NRFx_SPIM examples but the SPIS seems to always send corrupted data over the MISO line....
