Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
NCS 1.8.0
Modem FW 1.3.1
For other products I've worked on with cellular modems, we would add in back-offs to the firmware in the case we failed to open a PPP session...
Hi,
I've been playing around with the attached low power mode example. It seems to be written around the nRF SDK, but I am attempting to build and flash from within VSC...
Hi Team,
We are working with nRF52832 and nRF Connect SDK v1.8.0. Our application needs to sleep (power save mode) for 5 minutes and every 5 minutes it should wake-up...
Fota used to work fine in SDK v1.7
No I have moved to SDK v1.8.0
I don't believe my software has changed, however I am getting an error when running as follows:
Any...
Hello,
I'm working on a custom board based on PCA10040, but it seems to be stuck at the function "lfclk_spinwait".
Comparing both schematics the only obvious difference...
Dear Nordic Engineers
Our customer use nRF9160 to develop a tracker.They found that their programs were relatively power-hungry.They tested the serial_lte_modem example...
Hi there!
I am trying to combine the SPI and ble_app_uart examples.
However, when I add the SPI part to the uart, it shows this:
I believe there is some problem...
In the demo in test \ v1.9.0\zephyr\samples\subsys\usb\audio\headphones_microphone , I found that only dual channel 16bit 48Khz audio can be recognized on the PC. the product...
Hi,
I am using ble_sdk_app_hids_keyboard example:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_hids_keyboard.html...
Hi
I used Toolchain Manager v0.10.3 to install nRF SDK v1.8.0 at Mac mini(Monterey - 12.1) two times get same issue.
The issue is Toolchain Manager just download toolchain...
I am using the nrf52840 on the Raytac MDBT50Q-1MV2 module. ( https://www.raytac.com/product/ins.php?index_id=24 )
I am supplying the module with 5v USB power to the VBUS...
Hi,
I'm currently trying to use littlefs as the storage backend for the settings subsys and the internal flash for the actual memory. LittleFS is working in general but...
Hi,
I am using two NRF5340 (one as peripheral and one as central) for our project. Both don't have any display and input capabilities.
For our use-case, I would like to...
Board: nRF52833
SoftDevice: s140
SDK version: 17.0.2
I've added OTA DFU feature to my application. I flashed pca10100_s140_ble bootloader and my application to my board...
We are using a custom nrf52832 HW configuration and the device is entering a state where it's drawing approximately 3mA without any obvious application layer functionality...
