Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I use my own programs and routines nrf5_ SDK_ 17.0.2\examples\ble_ peripheral\ble_ app_ hrs\pca10040\s132\arm5_ no_ packs Product Bluetooth broadcast cannot be searched Android...
Hi,
Using the Peripheral LBS sample, is there a way to add advertising data to use both the UUID and name?
I assume this is to be configured in the bt_data ad declaration...
I am using UART on the Fanstel BLG840F to communicate from the 9160 to the 52840. So far I have successfully been able to communicate from the 52840 to the 9160 but have not...
Here we go again .... I did read many posts in this forum but did not find an answer.
We need to CE test a small Bluetooth HID keyboard for a special use case. Our test...
I am running into the exact same issue described here: https://devzone.nordicsemi.com/f/nordic-q-a/53693/how-to-flash-application-after-dfu-bootloader/217434#217434 Basically...
Hi, Nordic Team
I’m getting started trying to use both MCUboot and NSIB for 2-stage secure boot on nRF9160, and use SEGGER as developed tool. I enable NSIB via “Configue...
Near as I can tell from v1.7 of the product specification, these two parts have the same footprint & pin-out because they're both aQFN packages (as indicated by the "QI")...
Hi Nordic,
NCS v1.8.0
Controller IC 1: Thingy91 - NRF52840
Sensor IC: Laird BT510 - NRF52840
Intro: I currently have 2 devices. A sensor and a controller. For the...
Hi nordic:
NCS1.8.0 , I added UART2 to the NRF9160 LWM2M sample, but it cannot send and receive, but the same code is put into the NRF9160 UDP sample and it can work normally...
Hello Everyone,
I would like to implement a random delay of 10 to 3000ms before my development kit start advertising itself.
I'm using nRF5dk v17.1.0.
How do i go about...
Hi,
I tried to combine the spi and ble_app_uart example. But I got this problem, and the program was stuck in this loop.
Here is what I did:
I am using the 17.1...
Hello all,
we are working on new project that should work for both role (central and peripheral). If I compile the sample "central_and_peripheral_hr for NRF52833DK_NRF52833...
Hi,
There are several files in the mfw_nrf9160_1.3.1.zip archive that represent the current version of the modem firmware. Which files should be programmed in the nRF9160...
Hi all,
I want to implement a calendar that can be used for many years with nRF52840.
Will leap years be corrected in the nrf5-calendar-example? I looked at the code...
