Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I'm developing two products that will communicate via ble_uart. Both products have battery, so I need to reduce consumption as much as possible. I'm currently using nrf52832...
Hello,
Im getting different behavior on my SoC depending on what power source I use. For example I tend to get alot of retranmissions from client to server if I have them...
Hi,
I have taken nrf_connect_sdk_v1.9.1 and build n=my application over it.
When I delete .git file from v1.9.1/zephyr/.git, then my west compilation don't occur.
...
I tried to open a program created by else one. The Output is shown below. I could not understand: Due to which warning abort ? There are many warnings.
Creating solution...
Hello Devzone Community,
My name is Ted, and I am continuing my effort to configure a Zephyr based, Nordic aws_iot sample app based firmware to run and support nRF9160 lowest...
Hey I am using a nrf9160dk and I am trying to get lte-ble to work I get the above assert failed.
Does anyone have an idea how to fix this?
I have the hci_luart file...
Hello,
My group has developed a board using the nRF52840 SoC and we are in the process of transitioning our firmware from the development kit to the custom board. Our firmware...
Hello,
I am trying to run the system_off sample project to measure some low power currents. The sleep works as expected but once it reaches:
It does not go into deep...
If I wan to use the nRF52 as a Radio and not support any protocols.
I am looking to use this as a base band waveform processor and transverting down below 1Ghz.
What is...
I'm attempting to create firmware using nRF Connect SDK. Thoroughly studied these guides:
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/getting-started...
I'm referring to nRF5 SDK 17.0.2. In 'external/freertos/config/FreeRTOSConfig.h', the value 'configLIBRARY_LOWEST_INTERRUPT_PRIORITY' is set to 0xf, but the nRF51/52 only...
Hello! I'm trying to use this low power UART sample: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/samples/peripheral/lpuart/README.html I have a problem...
I want to add compiler flags to my build configuration i.e _DEBUG, etc
My understanding is that a build is done by build task
nRF Connect extension allows to create a...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 Base source: C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\peripheral_hids_keyboard I add uart implementation from following...
