Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi team !
I'm facing issue when porting my code from nRF52840DK to nRF5340DK
I implemented SAADC acquisition, using Timer/SAADC/(D)PPI stack on both boards, handling...
Hello, the device name is being parsed ok, but the mfg data in scan response seems to be there but not sure how to print it out. Using ncs bt sample direction_finding_connectionless_rx...
Hi there,
I wanted to change the advertising name while running DFU bootloader (secure_bootloader_ble_s132_pca10040), so I basically added what I found here:
https://devzone...
Hey,
my Power Profiler Kit on a nRF52840 DK stops recording after some time with the error message " Corrupt data detected, please check connection to PPK."
The time period...
Hi All,
I am using s112_nrf52_7.2.0_softdevice with nRF5_ SDK_17.1.0 and Segger Embedded studio for nRF52805. My application code is successfully patched for nRF52805 as...
Hello! I wanted to know if there is a way where I can just send a simple string from the nrf52 to the nrf91 without using any complicated examples, I have been trying to modify...
Hi, All
Just wonder how to view the log info like below, it is used in peripheral uart example.
LOG_DBG ( "tx_done" );
which config/tool allow this please?
Thanks...
Hello, We are using the serial LTE modem on the nrf connect sdk v1.9.1. We are trying to receive a big message on a topic we have subscribe to, but the serial LTE modem crash...
I was able to interface a 9 axis MPU9250 sensor with nRF52832 via TWI. Now I want to read more number of sensor's data i.e., I want to read 8 IMU sensors data. Since, nRF52832...
Hello there,
I'm using a nRF52840. I would like to perform a complete flash dump. I have tried using an ST Link V2 and and openOCD. It was only returning errors and the...
Hi,
Im using: nRF Connect 1.9.0, Visual Studio Code. I have: a nRF52480-dongle a nRf5340_DK
I would like to have Samples (code), to have a loop through with the highest...
i have a code base which is originally run on nrf52832 dk and i want to port it to the pca10059 dongle i run in gcc env and successfully modified the definitions and includes...
Hi, I'm developing an project based on ble_app_uart example. My expection that is multi mobile phone can connect with my nRF. But, my nRF can connect and communicate with...
Hi Nordic! I'm using the nRF9160 with a micro sd card so I have a lot of storage. I was wondering if it is possible to retrieve a .hex file and flash it using LTE?
I'm able...
