Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hey, I'm trying to get a basic BLE with coded PHY (125Kbps) setup with on the fly encryption/decryption working but I'm running into a strange problem. I'm using a custom...
Hi, I want to use the nRF9160 in a project, where I need the antenna attached to the nRF9160 to be able to handle being 1000m below the sea-surface. It is an AUV that collects...
Hello,
At present, there is a problem. When there are a few broadcasting devices nearby but many active scanning devices that the active scanning is not easy to find devices...
Hi
I am using app_timer_cnt_get() like MIllis()
uint32_t millis() { uint32_t milli; milli = app_timer_cnt_get() /32.768; return milli; }
but when i connect the nrf52840...
Hello ,
i have successfully compile and run 'binky' and 'Hello_words ' sample code using segger .Now i want to test Uart communication with nrf9160 . (want to send string...
Hi,
we are following below link for DFU example i.e. serial dfu on nRF52833. we are not able to install mcumgr in windows . are we missing anything here. kindly help us...
I'm testing an implementation of the serial UART bootloader for DFU. Firmware update using nrfutil works fine, using a serial-USB dongle, The only issue I'm seeing is that...
Hi DevZone,
I have recently updated:
nRF5 SDK to 17.1.0 from 15.3.0
S140 to 7.2.0 from 6.1.1
SES to v6.20a from 4.16
The SoftDevice now fails to initialize when...
hi support team,
in ncs llpm example, we tested it and find out one problem, why 4bytes of timer data would spend more than 1ms? please see picture 1.
further more,
...
I testing asset_trcker_v2 and want to add new custom event module. I have few doubts and queries:
1. There is event_handler function in each module as well in main fuction...
Hi,
I am working on the nrf5340 with zephyr (NCS 1.7.1), I need to monitor the voltage of the battery, in the beginning, I used the ADC API of zephyr, and it works well...
Currently I have a 52840 peripheral running peer manager. We bond/peer with it using a passkey system from an mobile phone central. It works great.
SDK is 1702 nrf5.
What...
I wanted to confirm that on the nRF9160, it is acceptable to tie the VDD and VDD_GPIO pins to the same 3.3V rail and bring them up together. The VDD_GPIO rail will not be...
