Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
we have a zephyr application on nRF52832 DK with nRF Connect for vscode
Before we added DFU support, we had a power consumption of 28 uA
After adding DFU support...
3 months ago Nordic stated the following
The S140 version 6.0.0 SoftDevice does not have full support for S=2 (500 kbps). The application cannot select S=2, so all packets...
Hi Nordic guys,
I'm developing with nrf5340, and meet some problem with writing external flash - nrf qspi flash.
I found it sometime failed in 'flash_area_write' and return...
Hi,
I'm using SDK17.02 on nRF52810, when my application have an error, it will log "fatal error" but never reset system. BTW, I'm not debugging and just watching the RTT...
Hi
I want to update the ble advertising data in my program. In nrf5340 the bt_le_adv_start() command should run only once in the main program.
Is it possible to change...
I 'm developing a program (C# ) on PC for the nRF52840 dongle (pca10059) that is a RSSI scanner.
Scanning different BLE channels in the environment. The program is much...
Hi Sir,
We plan to test the WebUSB example under the below path:
/ncs/1.8.0/zephyr/samples/subsys/usb/webusb HW: nRF52840-DK When we compile, program and connect to the...
I bumped into some compilation errors regarding PRS box4, when I tried to remove UART from an example.
I saw that PRS is "Peripheral Resource Sharing", but it looks like...
I am working on nRF Connect SDK 3,9.3 version. One day a dailog to update appeared. I clicked to update while SES was also opened and I was working on a project. Suddenly...
Hi,
I am working on a firmware and have added custom services to HRS example on SDK 17. I want to know if its possible to add BLE multiperipheral capability to my device...
I don't have enough pins to dedicate a SPI bus to the nRF21540.
In the webinar I attended I believe I heard that the SPI bus is not supported by the current SDK anyway,...
Hello everyone,
This was discussed before, elsewhere ( link) , however, it is meant for the "nRF51422 chip " and I need to resolve some other points too ...
it is necessary...
Hi,
I am working on the sample DFU OTA project as recommended below,
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu?CommentId=3cb5df69...
I am developing an applicaiton to run on the app core of an nRF5340, and I have mcuboot enabled for the purposes of handling DFU.
I have recently implemented signing the...
