Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello, I am having a problem with the development on a custon board. During system-off I wake up the chip with nrf_gpio_cfg_sense_input function on PIN 5. The chip wakes up...
Hi
I am designing a new BLE device and have some questions about the PCB antenna.
The product will be worn on the body.
I have a 4 Layer PCB with 1.0mm with and 35u...
I have a new nRF52840-DK connected to a Mac (M1 MacBook Air, Monterey 12.2.1). The nRF Connect Programmer sees the device (first screenshot below) and the JLINK disk mounts...
Im trying to use the BLE LTE Gateway running on a NRF9160DK
I have the NRF52840 running the lpuart_hci code and that is working fine i can configure the BLE from the NRF9160...
What is the canonical way to get a custom nRF52-based board into Nordic Connect SDK and/or Zephyr? We have developed a couple of custom evaluation boards for nRF52820, nRF52833...
I have nRF9160DK kit. The iBASIS SIM does not work in India. I aaranged a M2M SIM from Voadfone. The Vodafone SIM has 20 digit ICCID printed on it, while the nrfcloud accepts...
Hi
Im am struggling getting nanopb to parse proto files in NCS toolchain zephyr context.
It appears that the python38 embedded in NCS toolchain does not include all standard...
SDK version - 15.3
Segger version - 5.42
DK - nRF52840
I'm a beginner and I was following this tutorial our_services . The code given in the tutorial worked for SDK...
Hi
I am testing nRF52833 UART DFU function, but there is an error in merged HEX file,
Parsing input files. Merging file "SD.hex" into output. Merging file "APP.hex"...
When associating a pin with the UART, is it possible to still configure the pin to be open drain and with a pullup, or does the peripheral associating override those sett...
Hi :) ,
I'm using TWI to connect a sensor that i supply with an LDO regulator.
This LDO has an enable pin controlled by P0_23. Driving current is max 1uA so i configured...
In our project, we have defined 5 FDS_VIRTUAL_PAGES each of size 1024 words and have programmed to do GC if > 10 records are deleted. I see the 1st page being used for storing...
i have installed segger ide and nrf connect for desktop for programm nrf9160 , i have successfully uploaded Blinky code (zephyr) .but now i want to create a new project ....
Hi, I am trying the MQTT_SIMPLE sample on both the nRF9160DK and my own custom board. I have mfw_nrf9160_1.3.1 on both nRF9160 and I am using SDK v1.8.0. LTE connection seems...
Hi,
I'm using NCS 1.8.0 on a nrf52840.
I've got what seems to be a corrupted external flash Settings file. The issue doesn't seem reproducible yet, but as it happened...
