Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Setup: Windows 10, nrfutil verison 6.1.3, python 3.10.2, nRF 5 SDK 17.0.2
I have a custom board running the stock DFU firmware from the nRF5 SDK. The only changes we made...
There are many questions on DevZone on modifications to NCS peripheral_uart/central_uart NUS example applications to support higher throughput.
We have been mostly successful...
I would like to use the nrf connect sdk to connect to a device and 'discover' the GATT services it supports, the characteristics in each service, and then read the descriptions...
Hi everyone!
I ported some project from NRFsdk 17.0.2 (all works fine) to Zephyr rtos and faced with issue - when set high speed uart (460800 - 921600) then some bytes ...
Hi All
A few times ago, I installed the nRF Connect for Desktop v.3.8.0 on my PC.
Getting started assistant, Programmer, Toolchain manager apps were installed and everything...
I want to know about following things:
1). NRF_SDH_BLE_GATT_MAX_MTU_SIZE
2). NRF_SDH_BLE_GAP_DATA_LENGTH
3). NRF_SDH_BLE_GAP_EVENT_LENGTH
4). Connection event length...
Hi There,
I facing one critical issue with softdevice, I cannot get it work in freertos environment.
Hardware: customized board based on PCA10056
SW: nRF5_SDK_15.2.0_9412b96...
HI
I am using the I2S on the nRF52840DK I have constructed an array and all works well except once I start it , it continues to run, I cant get it to play the sample just...
Hi,
In the product I developed, there is a UI flow about the mode of pairing and binding, which has a limitation that it can only be paired and bound when entering this...
My nRF52 only advertises NUS.
When a phone connects (Android or iPhone), I want to force bonding.
It seems to be related to security. I have tried a couple things, but...
Hello ,
I am using nrf52810 and i have my own code and once its compiled hex file is created so if in case if i missed my source code and i had only my hex file is it possible...
HI I am using nRF52DK as central and peripheral. UART example was used in nRF52DK as central, and blinky examples were put in the rest of nRF52DKs to test the connection....
Hi,
Disconnecting connection during DFU, then DFU never works again.
I reboot device many times.
Application works fine and soft device works fine, buf DFU still fails...
Dear Dev-Zone Team,
I just got my PPK2 and wanted to test it on the nrf52840
It seams to work fine, I can see the advertisement peaks, however the average power consumption...
I am using vscode with NCS 1.9. I am trying to add RTT logs to MCUBoot as the product I am developing won't have an exposed Serial port. I started with the hello_world example...
