Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello, All;
Using your nRF9160 chip to develop, there are some questions when using the network and positioning, Hope to get your answer:
1. Can LTE work at the same time...
Hello,
I have two projects, one for the application core (modified BLE Peripheral sample) and the second is for the network core (modified HCI_RPMsg sample). I am currently...
Hi all:
condition:
SDK14.2
PCA10040
example: ble_app_uart_c
I have a central device ,it need to scan RSSI value of peripheral.
If the RSSI is more than threshold...
Hello,
we were using the HRS example as a starting point and modified it for our application. Everything works fine, we can see our custom characteristics, control our device...
Is it possible, without having to join ZOI, to recompile the Zigbee ZBOSS NCP Host for the Raspberry Pi?
The NRF Connect SDK documentation under ZBOSS NCP Host states :...
Hello,
we have an custom made board with a module from raytec MDBT42q.
Our application based on the nus example.
On port 0.7 we have a led.
It seems, that there is...
Hi
How do I configure a custom child image for the network core on nrf5340dk? We're using Zephyr RTOS, and want to do a multi image build when building the application ...
Hello, I would like to know if the Power Profiler Kit II could be used to measure current consumption on the Thingy:91 ?
In the Thingy:91 documentation, it is suggested...
I want to add a simple GPIO pin that act as output pin, in the peripheral_uart example .
in main.c
#include <drivers/gpio.h>
//#define GPIO0_LABEL DT_PROP...
I'm using ble_app_uart_c project in nRF5 SDK 17.1 with SES.
I got 2 different devices, one is ARC EM9D AIoT DK (as Peripheral) and another is nRF52840(as Central).
I was...
Hi,
nRF9160 with SLM NCS v1.9.1 fails to attach after 7th RESET (by RESET pin) & attach without power cycle.
There is not any ERROR state reported by modem, modem fails...
Hi All,
I am using s112_nrf52_7.2.0_softdevice with nRF5_ SDK_17.1.0 and Segger Embedded studio for nRF52805.
My application code is successfully patched for nRF52805...
Hi,
I'm using the default software to check the acceleration values when there is a movement in the Thingy:91 on the LTE Monitor terminal.
The document says that this...
Hi,
I want to test of MQTT communication with nb-IOT network before going for development.
For that I have updated pre-built firmware on development board using nRF...
