Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
In order to protect my device from becoming bricked when APP and NET side implementation of RPC application differs, due to wrong version being flashed or OTA fails on one...
hi:
Use the https_client routine to send data after the socket is established, and then send the data after getting the response. The errno returns as 128, which can confirm...
hello Nordic
i am working with nrf52832, with zephyr, ncs v1.7.1,
the device has a sensor that sample at 26khz each sample is 3 channels of 2 bytes data. the sensor use...
Hi,
I want to use the MCUboot for the DFU and I have been able to configure it and flash it on the device so far (tested that it is correctly flashed).
But I need to make...
Hello,
I work with NRF52832 evaluation board.
SDK 17.1.0
I try to implémente DFU -> pca10040_s132_ble / pca10040_s132_ble_debug.
Applicatif is : ble_app_buttonless_dfu...
Hi,
I'd like to implement Keil RTX5 on my custom BLE project for the nRF52832 using the S112 SoftDevice v7.2.0.
We are looking to standardise as many of our projects as...
In my schematic design, my nrf5340 uses vddh power supply mode, and the output VDD does not mount any load. Is it necessary for me to connect each VDD pin together during...
I am a user developing using nrf52832. I have a question about TX POWER. TX POWER can be set to -40, -20, -16, -12, -8, -4, 0, 3, 4 by using sd_ble_gap_tx_power_set(). I tried...
When I use two nrf5340 audio DK to test the LE audio demo, the handset side always crashes. Especially when I move the DK that is used as the handset.I think that incomplete...
using NCS 1.9.1 - Zephyr - Segger Studio - sample code: bluetooth / peripheral_uart
I based my project on the sample, modified it slightly and it works well on a board with...
I'm using NCS 1.9.1 and Segger SES
Following Nordic's recommendation I first made a copy of BLE/peripheral_uart in order to preserve the original code and then used the...
Hello, I have a question.
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral.
I have a question about the output time of the advertisements. The...
Hi Nordic ,
My product is working fine but i'm focusing on improving consumption at maximum because it is working on small battery ( evoluated tpms application)
It uses...
Hi everyone!
Could anyone clarify a few questions regarding channel mapping?
1. Is that true if I want to use specific BLE channels I need to do it just once on a central...
