Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I ran into a problem. I am unable to disable or reconfigure UART1. Any changes to the file .overlay does not give effects. I paste into the file nrf9160dk_nrf9160_ns.overlay...
Hello,
I am using an nrf52832-based ble chip and try to communicate with cap1293 touch sensor. I'm using SDK 15.3 and started off from the twi_sensor peripheral example...
Hello,
I am using the nRF 52840 DK board. Using nRF5_SDK_17.0.2 I am trying to implement basic BLE advertising in my code. Also, I have turned on the RTT log. From the log...
As the title states, I'm having an issue properly configuring the overlay/getting the sample driver/program to build. I get the following build error
Error Code:
I get...
Hi,
In the SDK 17.1.0 release note (downloaded from https://www.nordicsemi.com/Products/Development-software/nRF5-SDK/Download?lang=en#infotabs ), the verification GCC compiler...
I'm trying to create a Zephyr Shell command where I can write a certificate to the modem. Putting the certificate in the command line doesn't work, so I was going to use the...
Hi
I'm using nRF52805 to realize the DFU function using the buttonless_dfu example project. I follow the instruction of this and use commands in this discussion .
After...
Hi I have an question about use ZB_ZCL_DECLARE_POWER_CONFIG_ATTRIB_LIST macro in case when only one battery used.
I'm trying to declare Power Configuration like this
...
Hi. I don't believe this question would be strictly be considered a duplicate. I have seen posts discussing the same issue I'm having, but resolutions don't appear to solve...
In order to use this application in nRF Connect for Desktop, I have just purchased an nRF52-DK. As I'm using macOS, I believe that I'm affected by the 64 byte limit and need...
Hi,
I am trying to interface WM8960 CODEC with nRF52832 using (I2S and I2C) .
Problem I am having is with TWI scanner and also sending data to the know i2c address . have...
SES 5.44
nRF52840-DK
GNU Arm Embedded Toolchain: 9 2020-q2-update from here
S140: 7.2.0
Project is C code only
Project Setup:
Linker Script File (copy from...
Hello,
I am a research assistant at the Norwegian University of Science and Technology. We have in the past been using the micro:bit v1 for our practical labs which purpose...
Hi, When I hook the nRF5340-DK board to my PC, the SEGGER J-Link OB debug chip bothers me popping up a GUI that exposes the board as a USB mass storage device. How to get...
I'm using Android DFU library 1.11.1 and occasionally I see "E/DfuBaseService: Connection state change error: 133 newState: 0" errors. It appears they happen when the initial...
