Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832. I want te retrieve data from a battery cell monitor which uses the LTC6804 from Analog Device.
...
Hi,
I need to capture time in nanosecs between 2 tasks, for which I am using the zephyr suggested time measurement code as in:
When I am trying to compile the above...
Dear DevZone,
our goal is to replace the RX side of an old system, which is using the nRF2401. For real-time capabilities, the Shockburst protocol was employed.
Reading...
Hello, Nordic Engineer
I use nrf52811 and SDK 15.3.0
In example 《ble_app_uart》, I added timeslot（ESB）
Run this code《nrf_esb_write_payload(&tx_command);》
Subsequent...
Hi
I use in my project Zephyr ssd16xx driver with Waveshare epaper and LVGL and everything seems to be OK, but there is a strange behavior, when the e-paper works longer...
STEVAL-STMDLTE WITH NRF52840 using UART
We are trying to integrate the STEVAL-STMODLTE Link chip into the NRF52840 for rapid prototyping.
Trying to interface nrf52840...
We notice that upgrading from nRF Connect SDK 1.8.0 to 1.9.0 was generating issues in our application. Now we notice that nRF Connect SDK 2.0.0 is dropping the Segger supprt...
how to get started with nRF_TWI_MNGR , for CTP , touch screen driver FT6206 , what are the necessary steps to follow . what are the call back functions in the nrf_twi_mnrg...
Hello,
We are using Nordic sdk 17.1.0, with segger studio of 5.70a.
Here we are trying to merge ble_app_uart example with ble_app_beacon example.
Actually ble_app_uart...
Hello,
I'm using nRF52832 and the SDK version is "nRF5_SDK_17.0.2_d674dde" ,
First I tried DFU over UART using \examples\dfu\secure_dfu_test_images\uart\nrf52832, and...
Hi,
I build the smp_svr sample for nrf52dk_nrf52832. I installed Go on my windows machine and I am able to run the mcumgr tool. When connecting Teraterm to the UART of my...
Even if i did the configurations i got this error because of the manifesting stage.
When i did the configurations which is like below,
west config manifest.group-filter...
Hello,
I am trying to use Direct Test Mode example on SDK v17.0.1 to do our product's pre-production RF tests. I can see expected results on nRF Connect Direct Test Mode...
Hi, While testing the new nrf5340 Audio DK and BIS example, I wanted to see how the Periodic Advertising Sync Transfer (PAST) data looks on the nRF Sniffer version 4.1.0....
