hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
The MenuConfig page of SEGGER IDE (ncs1.9.1)：
How should I configure this interface if I want to configure usb DFU and trigger upgrade mode via button: 1.boot_usb_dfu\Use...
I am trying to use the DTM example for nRF5340 DK (PCA10095). The example is located at "C:\v1.7.0\nrf\samples\bluetooth\direct_test_mode", but I am facing "NRF_RADIO_Type...
In general, what are the steps to adding a device using GPIO pins.
My thoughts are to physically connect my peripheral to the board and configure the device tree using an...
Hello Nordic Team,
I have a nRF52833 DK with me.
I am using nRF Connect SDK v1.8.0 and through that using Segger Embedded studio loaded the Light switch example to nRF52833...
HI,
I recently migrated my nrf52840 based devices to Thread and Zigbee SDK 4.2.0
I used to have a good power consumption around 100-150uA with zigbee enabled.
Since...
I'm considering using the NRF52840 for a device with infrared proximity sensors that requires 8 IR LEDs to be driven at around 14 mA successively (never more than one at a...
Hi Nordic community
We have a custom IC to interface with the nRF52840 chip. We did testing for that IC with FPGA and the related control, clock signals are as shown in...
Hi guys,
We designed a custom board with the nRF52840 SoC and is trying to use the QSPI interface to communicate with an external flash AS5F18G04SND-10LIN.
We are having...
Can someone point me to where I can find some information about the secure vs non-secure builds and what considerations are required for either? Currently I'm trying to create...
Hello,
What is the difference between 2 devices which are constantly scanning and 2 devices which are connected? Also, how do I code 2 devices to connect to each other?...
Hello,
I am going off a fresh install of nrf connect desktop and installed the 2.0.0 version of the toolchain from the toolchain manager. When i create new project from...
Dear all
I am looking for a tutorial like this https://devzone.nordicsemi.com/guides/short-range-guides/b/bluetooth-low-energy/posts/ble-central-tutorial
It sounds quite...
Hi,
The manual for nRF5340 DK states: "VDD can be set by the nRF5340 firmware". I need to set the VDD to 1.8V. How is this done? I can't find any code documentation on...
I am running Version 1.9.1 of the NRF SDK, am programming in VScode, and have written my own custom board and associated DTS files for the hardware we are implementing.
...
