Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Dear,
We enabled QSPI DMA Encryption to cipher the external QSPI communication with enabling NRF_QSPI_HAS_DMA_ENC. So, QSPI DMA communication worked well.
However, when...
Hi,
This might be a simple answer, but I am working a BLE app which I started from the zephyr peripheral example provided in the nrf connect sdk. I removed the cts service...
Hi,
I'm upgrading our RCP firmware that runs on a custom nrf52840 dongle. It was using openthread bare metal on an old version (clone of openthread repo and run make -f...
Hi,
I am develop with nRF5340, ncs1.5.1.
I am puzzled how to read the value of an output GPIO.
I saw the function gpio_pin_get_raw and gpio_port_get_raw, the comment...
Dear Team,
We are developing HID remote with BLE audio feature which support windows platform.
In the NRF52 smart remote 3 BLE audio support only for Ubuntu.
My Queries...
Hi team!
We are working nrFready smart remote 3 with windows 10 pro operating system.
When we paired the given remote (with battery operated) with the windows device via...
Hey all,
I am starting a little research on how to use my NRF51 DK to control a relay in order to turn off/on 220v operating devices.
I dont know much about electronics...
I'm currently working with a client who is implementing the nrf9160 into their product. They had a version of PCB made which connects pins 104-127 to ground, even though the...
Hello,
We need a bluetooth BLE module, for UART communication with AT command.
with certificatation EN300328 V2.2.2. Do you know where we can buy them?
If we use the...
we are using nrf52805 after in few devices sometimes BLE is not visible(stopped broadcasting) to the receiver.
Here are the observation on that faulty device:-
1. Device...
Hi Team,
we are working on smart remote 3 implementation using nRF52832 with Windows 10 pro operating system.
we tried to connect this remote with laptop using the...
Hello Devzone,
With an nRF9160 based project and lowest power, lowest current consumption in mind, is there an explicit I/O pin setting to make via Zephyr API for the nRF9160...
Hi
Now I am using NCS1.7.1 for development the nRF52840 chip.I need to use the C standard library(math.h).I set up as follows:
There is no problem when the above macro...
Hi,
I would like to know the functioning of CPFD (I would like to represent the characteristic value as IEEE754 float32) I am not aware of how can I implement this. for...
