Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
Since BLE advertising consumes current, I want to stop sampling ADC data during BLE is advertising. Are there any BLE events to know when advertising happens or are...
I use the zephyr version 3.0.9 for DF.i use the both boards nrf52833dk.i set the antenna array including antenna_num,antenna_patterns,and antenna_ref(pdu_antenna).
both...
Hello,
NCS1.9.1, VSCode, nRF5340DK, periodic_adv
CONFIG_BT_DEVICE_NAME="xxx" in file prj.conf.
how to dynamic change BT_DEVICE_NAME in main() start?
Best rega...
Hi everyone,
I am looking the schematic of nRF52840 (PCA10056) and I am a bit confused with the Power Sources (sheet 7 of 7).
There are three load switches that prioritize...
Hello,
My project:
- I have a low consumption project width BLE. - I'm using internal LF clock (I know it's better to use an external) - I use the Beacon example project...
Hello!
I am working on a FOTA solution for the nRF52DK, I have followed this example: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs...
Hello,
I've started to develop with the nRF Connect VSCode extension and enjoying it a lot. However, I've noticed when I share a project the build configuration doesn...
Hi,
I observed what appears to be the same issue as https://devzone.nordicsemi.com/f/nordic-q-a/51337/nrf9160-infinite-nrf_connect-blocking-behavior-post-lte-psm-wakeup...
Hi,
I'm trying to write data to a characteristic. This is a BLE led driver. I can successfully send 5 writes and then it stucks. All the 5 sends succeed - I can see the...
Hi
I need to Send one character from mobile. based on the character I need to glow the LEDs which is placed on DK. How can I achieve this is there any sample available for...
Dear forum,
We capture audio via PCM (10kHz, 8bit => rendering a raw rate of 80kBaud) on a BM833 and would like to transmit the data (one way) to a paired device using either...
Hi,
NCS1.9.1, VSCode, nRF5340DK,
Without external flash memory and not use mx25r6435f which on DK,
how does MCU store data (such as a series of serial numbers)?
and...
hi ，i want write flash by jlink，eg：write val 0xaaffffff to addr 0x76000, only write 4byte.
but when i write, err "flash not erase" occurred，
I don't want to erase this...
I try to onewire communication for DHT11 but I couldn't it . I decided uart instead of onewire. The different microprocessor will read the sensor data and send it via uart...
Hi,
I'm trying to combine OpenThread, MCUBoot and LittleFS in a sample in nRF Connect SDK v1.5.1, but I'm getting the following error:
I have checked the file, and it...
