I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Do you have an updated schematic for the latest nRF52-DK development board? The board I have from July 2022 (reference # 0365RUBR) has some differences compared to the online...
Hi there,
A couple of weeks ago, I'm facing the issue that my nRF52840DK board is not visible and led5 is flashing rapidly. I reflashed the bootloader, j-link-ob-sam3u128...
I added some functionality to asset_tracker_v2. I used two pins of Nordic chip for following purpose: 1. Detect BMS, pin as Input 2. Reset BMS, pin as output. The pins overlay...
Hi,
I'm a newbie of microwave board design, after many research I finished our 2.4G USB Receiver board which use the nRF52840-QIAA. But I still want some advice of the RF...
Hello,
My setup is UDP sample and PPK2 for power measurements. I am trying to figure out the best settings that are available with eDRX set to <= 20.48s, and preferably...
Hello,
I am trying to get the data out of an out of the box zigbee sensor (PIR motion sensor) with the CLI example provided.
I flash an NRF52 with the CLI example, and...
We are working with tuning of the GPS:
Basically the tuning is fine but we are mostly bandwidth limited.
I wanted to ask how much is the acceptable bandwidth for a GPS...
Hi Team,
I am working on air mouse development using NRF 52832.
nrf standard package support ICM 20608 with AIR_Motion Library , but its not available now in https://www...
Hi,
I have noticed that when a peripheral (using NUS) is disconnected from a central it takes 2-3 seconds for the peripheral's BLE_GAP_EVT_DISCONNECTED to trigger.
Shouldn...
Hi,
I encountered that the PWM couldn't be closed completely, it still has about 100uA after PWM is uninitialized.
For troubleshooting purposes, I have posted my code...
I am working with SPIS on nRF5340. Since my RX and TX buffers will not change, is it possible to call nrfx_spis_buffers_set only once, during initialization? I tried to do...
I am creating the Battery characteristic in a Battery service but I run out of memory (0x04 error) when generating the characteristic. However, that makes no sense. I have...
We’re using Nordic Semiconductor nRF52840 and we may have some problem with RTC when we simulate a brownout. In our application we have both coin cell battery and external...
