I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
HI,
I'm trying to configure the MCUboot / Netboot with an external QSPI flash. I can do it for the APP core with MCUboot, however I get lost how it work with the NET core...
Working on a proof of concept demo that will use bluetooth mesh (Proxy and relay nodes). and want to select the right development kit. Was looking at the nRF5340 DK but the...
Hello. I am using NRF SDK 1.9 version + VS Code to process accelerometer data. NRF52840 + ADXL375 The accelerometer is configured to issue an interrupt under a certain condition...
Hi,
I'd like to add the capability to perform secure DFU over USB with the secure DFU BLE bootloader as a baseline. What needs to be done to achieve this? In addition...
Dear Nordic Engineers
I would like to sample the ADC between advertisements or connections, that is when the RF is sleeping, so I want to use Timeslot, I see there is a...
I am trying nrf52840. The conditions are as follows. -The development environment is SEGGER. -nRF5_SDK_17.1.0 -The evaluation board is a DK from Raytac. There are two identical...
I am developing code for nrf52832 to read data from a connected sensor on I2C. There are two scenarios I am trying to save power:
1- During the initial power up, I have...
Hello,
I'm starting a new project on a NRF52810, and i need to use the pairing feature in my application. As a result i need to compile the FDS driver. If i'm doing so,...
Hello,
I have setup a single master and multiple slaves (10 in number).
The master has master TX channel and the slaves have slave RX channels.
The slaves send data...
Hi, I am working on ble_app_uart_c_pca10056_s140 project. I have changed the following for power saving. Is this the right way to achieve this mode? After how much time it...
I used this code to convert my analog sensor data to digital with 5 khz continuous sampling and after that i want to sent my data to pc via BLE. In this code, NUS was used...
I'm using a custom battery operated board with the nRF52840, when there is no GPIO events for a specified time period, the device goes to a hibernate mode using the __WFE...
I am currently working with a dvk-bl653 working on increasing the speed of the DFU. I have a max packet size of 251 and have tried different connection intervals but only...
