I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi again
I have used nrfConnect to create an application from sample, the sample being peripheral_hr_coded
I have placed my custom service into the app, and it works...
Hello, I am trying to measure the input voltage on an nRF52833 and it is not behaving as expected.
The following code is taken from here and works as expected on any nRF52832...
Dear Sir.
I am using the cJSON driver .
When it comes to string it works fine .
However when I use integer and swap the lines
//cJSON_AddStringToObject(root, ...
I'm sorry my English is not good enough.
I am developing a product that works as a BLE peripheral using nrf52832 and NCS1.6.1.
In addition, the following statement is...
Hello,
I am trying to establish a mesh network with two nodes(self provisioned) simulating the Light and Light_switch examples without the provisioner. My plan is to play...
Fairly new to nRF Connect SDK & Zephyr although I have worked a lot with NRF5 SDK
I'm at a bit of a dead end here. I trying to setup a way to repeatedly read out data from...
Hello,
I would like to use littlefs in out Project and it seems to be very usefull. I read several documents and have the sample running on the eval board. But there is...
Hello,
I'm using the power profiler to perform current measurement of our IoT device. It appears to work well when running for a few minutes capturing. When I wrong for...
I am trying to use SPIM2 on an NRF52840 based board. The SDK is 17.0.2.
For the life of me I cannot understand how to 'consistently' determine the values to be specified...
I'm trying to modify the HTTPS sample to connect to Google Cloud Functions but I keep running into this issue where connect would fail.
1. I have disabled TLS peer verification...
We have a running project with nRF52840 + S140 7.2.0 - SDK: 17.0.2 + Bootloader.
I need to change the size of our bootloader in a production environment. This update must...
Hello,
We are currently certifying our module for Verizon in the US. As such, we are updating our software to work with MFW v1.3.0 and the corresponding NCS version v1...
Dear Nordic,
we developed firmware based on S112 and SDK 17.1.0. We have a problem with poweroff routine: at poweroff the status LED is ON.
this is part of our circuit...
Hi Team,
I am using nRF52840 on our custom board. I have enabled SMP for DFU and SMP image management in my build. DFU was successful for the 1st time but when I try to...
