Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
I'm trying to build a basic shell sample on a custom board based on nRF52840
In the proj.conf file I have
CONFIG_SHELL =y
CONFIG_SHELL_GETOPT =y
CONFIG_SHELL_BACKENDS...
I am new to Zephyr and I have been trying to get hold of a tutorial or a sample app that would indicate how I can use the UART on the nRF52832 for communications with another...
Hi,
I'm wrapping up a project which uses an nRF5340 as both a Bluetooth peripheral to advertise etc and also as a Bluetooth central to scan for devices (not both at the...
I recently started development on NRF52833 for one of my projects. I use segger embedded studio with the " ble_app_uart " example. As I mentioned I'm using nrf52833 DK so...
I want to recover DFU over BLE upon a dropped connection while in the middle of an update.
I have my own software that I've cooked up to program from another NRF52 chip...
Hi,
I see you have what appears to be a working implementation of OOB/NFC pairing over iOS here ( https://github.com/NordicSemiconductor/IOS-Nordic-Thingy ), which doesn...
Hi,
Here is my previous ticket.
https://devzone.nordicsemi.com/f/nordic-q-a/83856/channel-interference-at-nrf52840
I haven't had response tho that's why I made a ticket...
Hello! We have an application that I need to implement Tensorflow Lite. We started with the Arduino Nano 33 BLE Sense board, which had a TFL library on it. After using it...
Hi,
For 52820-QDAA, what load impedance is preferred seen into the matching network? I mean the total load impedance of C3, L1, C4, L2, RF trace and antenna.
Since our...
In our application, we've enabled full modem firmware update, which requires us to enable CONFIG_NORDIC_SECURITY_BACKEND. When we also enable memfault, this compile time pre...
I am build an application with features : When I not used nRF it imediately in sleep mode and be wake up by BLE events to send some text, and return to sleep mode ( the reson...
Hello there, Thanks for writing an application layer for SGTL5000. https://github.com/NordicPlayground/nRF52-teensy-sgtl5000-audio
I've configured the SGTL5000 to source...
We have a simple coin battery powered BLE device with a Laird BL652 module which has an nRF52832 chipset.
We have three buttons and set it up as low power as possible...
Hi, I downloaded a project from Git. I tried to open in SES using nRF Connect SDK. During the initial Cmake, the error occurs as shown in attached image.
Hello,
Our aim is to install "pc-ble-driver-js" and use the connectivity board for the serialization process.
We are following this link to get this working https://github...
