I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I'm using the nRF52840 on a custom board along with an ESP8266 (ESP-12S) Wi-Fi module.
The ESP module prints out a bunch of information at a weird nonstandard baud...
I am having trouble setting up DFU over BLE in nRF Connect SDK. I am using NCS 1.9.1. I have followed these instructions with my own project on both the nrf52840 devkit and...
Dear All,
We are developing a device based around nRF52840 on a rigid-flex custom PCB that is mounted inside an anodized aluminum cube with one face covered with plastic...
Hello, I'm trying to get an LPN to unprovision itself based off of an external command. I tried to base it off of the examples so I simply call: However after the reset it...
Hi,
I have my device based on the nRF52840, we have manufactured some equipments and we have created our own application to manage connection. Everything is working fine...
Hi all,
we recently had a problem with couple of our boards based on Raytac MDBT50Q-1MV2 (nrf52840 + osc. + antenna). We base our app on Zephyr. After programming some boards...
Hi, I've been tasked with doing some development on the nRF24LE1F on one of our legacy products that was designed many years ago! I'm in process of converting the code to...
Hi,
I'm trying to use UART1 for console and shell, for example to be able to log messages on VCOM0 linked to UART1 of my nRF5340 DK board. The example that I'm testing is...
Hi Nordic team
Customer Delta was running a street lamp project.
For AWS FOTA, they applied a AWS account and firmware update already can work.
However, it looks like...
Hello,
I am developing FW on NRF52840_DK for a BLE Peripheral as a Reader.
Reader to Mobile App Tx size is 32 bytes
Mobile App to Reader Rx size is 133 bytes.
When...
Dear Bluetooth Mesh experts, The firmware contains a proprietary message that sets a node's parameters and returns 100 bytes of data. The Android app sends it as an acknowledged...
Hi
I've configured Zephyr to run BLE host on cpuapp and BLE controller on cpunet, and using RPMsg to communicate between them.
When I call bt_enable() from the app core...
Hello,
I was wondering if there is a way to extract the "Device name" from the scanned advertisement data published by a model on a different node. I want to display the...
I'm trying to enable saving of coredump to flash. I'm running on nrf52840 with NRF SDK 1.6.1.
I have defined the following:
CONFIG_DEBUG_COREDUMP=y
CONFIG_DEBUG_COREDUMP_BACKEND_FLASH_PARTITION...
Hello ,
We are attempting to use the QSPI driver with an MX25 with 2 i/o lines instead of 4, essential SB 10 and 15 on the nrf52840 DK have been cut. However I am not...
