I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello, we have a thread that essentially is running a loop and we want that thread to be running for all the lifecycle of the app. If for whatever reason that thread died...
Hi Team,
I am using Open Thread networking protocols in my projects to communicate with the devices .I have seen while trying to changed some parameters over the network...
I am unable to do a FOTA with the SLM application on a nRF9160. When I try to do a FOTA with the command below, I get a 404 even though I know the URL exists (real host name...
Hello,
I have been working with custom nrf52832 board to develop firmware for my product. I have been trying to compile the example secure bootloader from the SDK v15.3...
Hello, I am developing a uart communication between the nrf52833 and the nrf9160. I found some examples but I don't want to use the HCI layer, I prefer to use the NUS service...
We have an application that wakes-up every N minutes and listen to devices in a ble mesh then performs many other actions. In order to save battery, we would like to power...
Hello
OS :- Linux
Hardware version :- BC805M
SW :- Segger embeded studio
I am using nrf52805. I am test it with ble_app_uart. It advertisement continuously and shown...
Hello,
I'm trying to transfer data to an L2CAP CoC on a nRF52832 from iOS and Android devices. I've configured the MTU and MPS so that the SDU fits in a single packet with...
I'm using BLE Mesh Sensor example that Client & Sever communication data each other.
Because I'm implementing one by one communication data that client > sever > client...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I'm trying to add a custom UUID in the advertisement packet and scan for the custom UUID in the central device to...
Hi,
Our firmware currently only support full modem update, and I would like to perform a full modem firmware update from 1.2.0 to 1.2.7. According to the reply from https...
hi，i use radio_test example for radio test. If I don't make any changes, the routine can run well, but a PA chip is added to my product to amplify the RF signal. The PA /...
I am getting a softdevice hard fault occasionally, on fully enclosed devices with no debugger port access.
Where can I find info on potential causes of this fault?
nrf51822...
Hi
I have been able to work with the 'Lighting' demo BLE mesh application using the nRF Connect SDK with Visual Studio Code. I have even been able to add my custom board...
