I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
HI
I am beginner, I have a question , is necessary to put both crystal in circuit configuration?,
in my application i am using nrf_calendar example like a watch, may be...
Hello, I'm trying to set up the DFU over the air mesh. Using the mesh SDK 5 and nRF SDK 7.1.0.
Using the DFU example from nrf sdk17.1.0, I successfully ran it.
When I...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
SDK17.2, keil5,nRF21540-DK
my project use i2c and spi, but got error:
Error: L6200E: Symbol SPIM0_SPIS0_TWIM0_TWIS0_SPI0_TWI0_IRQHandler multiply defined (by...
Hi,
I have a custom board with nRF52840/SDK 16/Softdevice 7.3.0 using Secure Dfu Bootloader. On my Android device I use Nordic Dfu Library. I have tried all available Dfu...
Hello,
SDK17.2, Keil5, nRF21540-DK,
when change DCCH to 3.3V as above codes in main first,
(1). the uart will can not work ,
(2). change pin to high voltage as follow...
I get some message from Nordic.I want to give my IQ sample to MQTT.i see that they give me information about a API of MQTT.
But i can't use it,can you give me the more information...
Hello,
I'm trying to move from nRF5 SDK with nRF52840 to NCS with nRF5340 and experiencing a lot of problems replacing the nrf driver functions with nrfx.
Thanks to...
Hello !
What extra field need to be included ti MAXLEN calculation in case of Ieee802154_250Kbit radio ?
CRC , len ? I try to limit total amount of received bytes but...
I have an applications that was using NCS 1.7.1 in its west manifest. I am going through the process of upgrading to 1.9.1
My application using zero latency IRQs and sets...
Hi,
I have nrf52832 dK and know how to configure them in code.
I have studied BLE supports the LE 1M phy and LE 2M phys from BLE core specifications.
I know about the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi devzone, I've had UART communication problems between nRF52 and a BG96 modem for a long time.
today I added a pull down resistance on the rx of the nRF52 and it works...
Hello I'm trying to get the lower consumption with this EvK in power off mode. I was expecting around 0.5uA but the minimum I get is 1.8uA ~ 2uA.
The measure has been done...
Dear All
I tried to connect to an apple device, it is successful but soon after that, it is disconnected with reason code 0x13 - terminated by remote user, I tried to change...
