I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello.
I read this article
https://devzone.nordicsemi.com/f/nordic-q-a/66914/uart-current-consumption
I did my testing with ble_app_uart from SDK 17.0.2 on a nRF52832...
Dear all,
I am now using several pairs of nrf52840DK and nrf connect sdk v1.7.1,and using llpm(low latency packet mode) to send data.
In our system,there are four pairs...
Hi,
I have an issue where sometimes after a restart of our device the nRF hangs on either: ble_dfu_buttonless_async_svci_init() or ble_dfu_buttonless_init(&dfuButtonlessService...
Hello all,
I have 2 problem that I can not understand why.
1) Now cdc_acm isn't working anymore, but until 2 days ago it was working perfectly. I didn't change nothing...
Hi, I'm developing an application tracker device using 2 libuartes, pwm, ble and now I am going to approach reading battery level. After I research on dev zone but I only...
There is already a case on github:
https://github.com/zephyrproject-rtos/zephyr/issues/44586
But essentially we see an issue with nrf5340, where we get random crashes...
HI,
I have tried to read the I2S data by using nrf5340 and I successfully did that. Now, I want to work on the sample with BLE. for that I have made some configurations...
Hi Team,
We have nrf52-DK with version 2.0.0 and we are trying to do power analysis for our application using it. We found a description in nRF52_DK_User_Guide on how...
Hi everyone. I faced with some issue. My device has power source. This source is solar panel and capacitor. Device should work after sunrise only. Sometimes in the morning...
- I Can't debug nRF52810 using Keil µVision V5.36.0.0 and PCA10026 as segger. I get the message: "No Cortex-M Device found in JTAG chain."
- Using the Programmer v3.0.0...
Hi! I have some troubles understanding the register Erase Protect and before using that I need to understand it more clearly.
I understood that if I activate that register...
I am testing the RTC example in nRF5 SDK v17.1.0.
This example shows LED1 switching at a rate of 8 Hz and LED2 lighting up after 3 seconds.
This is confirmed.
The programme...
Hi Nordic,
We are preparing to validate a product that contains the UBlox BMD-340 with the Nordic Softdevice. We would like to use the Nordic Semiconductor “nRF Connect...
I have a problem with sagger embedded studio I have downloaded latest version for m1 MacBook Pro (I have m1 max version of MacBook) and I have this problem I am using Segger...
