I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
I would like to fast adc some analog signal from my opamp PCB. I am using nrf5340DK SDK1.9.1 with VS Code.
Got the example code nrfx_saadc.zip from and my first...
Hello!
I have used most of the GPIO pins on the nRF52DK, and most of them work. But I cannot get pin 21 to behave. I want to use it as an input. I have configured it as...
In nRF_SDK_For_Thread_and_Zigbee, on the nordic BSP package following three-button functionalities are available:
#define BSP_BUTTON_ACTION_PUSH (APP_BUTTON_PUSH) /**< Represents...
Hi,
I have 2 boards, one with monogoto esim and one with ibasis esim when I try with monogoto everything is working fine
when I try with ibasis esim i can't get registered...
Hi all,
I have a problem when I try to debug nRF52832 target. The nRF52832 chip is advertising properly but as soon as I enter in debug mode, advertising stops. There is...
I am using 9160 to develop a customer's product, which needs to reduce power consumption as much as possible to prolong the battery life of the product. I know that 9160 communicates...
Hi,
We are using a self-developed python script to connect to nRF52840 in our products. The product contains many custom 128-bit services and characteristics (30+). These...
Hello,
I am working with a sensor that generates a simple crc8 XOR on based on this code from the nrf sdk 17 and sends it to a central:
I need to check this CRC8 on...
Hello Devzone,
While developing an nRF9160 based, battery powered device (working on the firmware piece of the puzzle) I have run into a couple of issues in my effort to...
Hello, I am looking into using zephyr with a host controller configuration on separate chips, where the controller is an nrf52832 chip. I was wondering how would the power...
Hello everyone,
I am developping on a nRF52840 using sdk-nrf v1.8.0 and Nordic MCUboot fork as bootloader.
For security matter, we want to use the HW keys MCUboot options...
HI,
I am developing a device that acts as both a peripheral and central device. This is working ok together, but I have one thing I cannot figure out. I separated central...
Hi Nordic Team,
Just following up with this post, I am not able to write anymore since the post is locked.
if I define 3 instances of fstorage, can I have 2 fds instance...
Hi,
We noted in the errata (Issue 133) that the radio performance is significantly degraded if the QSPI is enabled. The suggested workarounds are to 1) lower Vdd to 1.7...
I am creating a Matter accessory device with the nrf52840dk and the guide on https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_matter_creating_accessory.html...
