Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Is there any zigbee example for nrf52840 dongle (PCA10059) ? If not, what is additional changes needed to add support in existing examples?
I unable to run the zigbee switch...
Hi, I need to add Azure IOT connectivity to nRF5340DK. I have already tested NodeMCU based data upload to HTTP based server and successfully working. Now, to divert the data...
I am trying to upgrade SoftDevice and Application firmware from v6.1.1 to v7.2.0 on Nordic USB840M dongle and I am facing a strange issue after such upgrade.
Please find...
Hi,
I have created my own service and charecteristic
1. But i am seeing only unknown service - How to give a name to this service
2. I am getting unknown charecteristic...
Hi
I have compiled (successfully) the Zephyr example samples/bluetooth/peripheral example for the nRF52 DK (nRF52832).
I am going through the code and trying to understand...
Hi
I have developed a device using the nRF52832 and I am wondering if there is built in functionality to reset the chip back into bootloader mode without programming the...
Hi All,
I'm using SDK17.1.0 and I have a question about mobile device subscribe.
I asked this question before, but the engineer didn't reply, so I asked again, thank...
Hi All,
I want to port BPS to my custom project, I encountered the problem as the title.
When I connect and trigger the subscribe like this picture.
My project will...
I have code that runs for around 5 days, then for some unknown reason hangs or stops running, which makes it almost impossible to debug.
I have also tried to implement interrupt...
Hi.
I have an issue that, If I power off Master and do save flash at Slave side together, the nrf_fstorage_is_busy(p_fs) return value always true .
When BLE is connectting...
I added a mesh shell module to my firmware running on nRF52480 .
Opened the mesh shell
uart:~$ mesh init Mesh shell initialized
mesh provision 0 0x100 0
Crash (see...
I've been slowly adding NVS functionality to my code. Has been working fine, up until today when I attempted to write a struct I have for storing historical data to flash...
Hey,
I have implemented BT FOTA process for my zephyr based application. DFU over Bluetooth works fine. But now I struggle to implement manual upload of image (it will be...
Hello Devzone,
My name is Ted. Recently I posted here and received some good help on low power sample code for the nRF9160DK board. This code helped me prove in real life...
I'm currently trying to set up a simple demo using 2 dev kits running the SPIS and NRFx_SPIM examples but the SPIS seems to always send corrupted data over the MISO line....
