Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm trying to use parity UART communications with the nrf52840 using nRF Connect SDK v1.9.1, but I'm getting an error -134 when I call uart_configure().
When I use UART_CFG_PARITY_NONE...
Hi,
As mentioned in subject line, I am trying to enable BLE SC peripheral in SDK 17.0.1 with softdevice S113. I have enabled the PM_LESC_ENABLED macro in sdk_config and...
Hi Nordic,
My customer has imploy nRF52832 to develop a heart rate equipment.
We have test the ble_app_hrs_c and ble_app_hrs on two nRF52 DK.
I found that if I comment...
Hello Dear,
Why the time of uplink state is 950 ms if the data packet size is 0 Byte?
Can we say that every time a data is sent, it takes 950 ms to get the transmission...
Hi nordic, In the products I developed, since the entire product is metallic, only a small part is a non-metallic material, and an antenna has been designed to solve the problem...
I've had a lot of server errors on https://devzone.nordicsemi.com/ lately.
This happens more often than not on chrome/ff/edge/incognito/etc.
The one thing that seems...
In our cases, Serial interface needs to support Heartbeat of Configuration Server.
But configuration server's heartbeat handler is not support serial interface and serial...
Hi,
1. What does signaling test mean in bluetooth domain?
2. What does non-signaling testing mean in bluetooth?
3. In the Bluetooth world, I only know about DTM testing...
Hello.
It is under development using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I am investigating how to do bonding with iPhone. As a way, bonding is...
Hi,
I have been able to program my NRF 52840DK with the following program: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/central_uart...
Hello Everyone,
I am using NRF52833 in my project. My code is FREERTOS based. I am also using 2 UART, one is normal uart and other is LIBUARTE. I have also initialised timers...
Hello,
NCS1.9.1, nRF5340DK+nRF21540EK, Windows10 X64, VS Code,
not find [nRF21540EK_nRF5340],
about software: how to create project build?
are there any samples? ...
