Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I did respond to this:
https://devzone.nordicsemi.com/f/nordic-q-a/86426/peripheral-and-central-uart-sample-crash-when-sending-longer-messages
I do not see a update...
Hi, I have been learning my way around SES, nRF Connect SDK, nrf52-dk, and the sample projects for some time now.
When I wish to open another sample project, I follow the...
I program the uart example in my board nRF51 dk. I put a osciloscope in pin 9 and the signal is a square wave between 0 al 30V. So i think that the protocol is RS232, is this...
At a rate of 1M, the receiving sensitivity of the Bluetooth chip was tested, and during the test, it was found that the sensitivity may decrease whenever the frequency point...
Hi
We are working on an algorithm applicable to the indoor positioning of ships. We want to improve the algorithm further on top of the existing algorithm for Bluetooth...
I'm on a Comcast cable modem connection. When I've tried to pull up this site over the past few days, I've gotten "The page cannot be displayed because an internal server...
Dear nRF DevZone,
I have question regarding Zephyr k_sleep() function and NRF52840 timers.
I am developing an application for nRF52840 SOC and for that I am using nRF...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to pair from "Settings"-> "Bluetooth" of iOS (iPhone 12 Pro). For pairing...
Hello,
I am developing an application that requires use of some of the traditional C "stdio.h" functionality. My current development setup is the nRF5340 DK running Zephyr...
I'm using sdk for mesh version 5.0.0, sdk version 17.0.2 and my board is nrf52840-DK.
How can i keep mesh config after wake up from deep sleep( system off).Plus, when my...
Hi,
This morning when I tried to access devzone, it says I have been IP banned. I have the same issue as this ticket:
https://devzone.nordicsemi.com/f/nordic-q-a/86922...
Currently running NCS 1.7.1, SUPL client 0.7.0 and MFW 1.3.0 it has stopped connecting properly from the last time I've played with it:
Not sure what's up there..
...
I am having trouble powering my uicc. I feel like I am just looking for some setting, but I have not found the right one yet and I am at a loss at this point.
What I have...
I used direction finding rx/tx examples(get 45 points of IQ data). I used the ref period IQ data (8 points) can caculate base phase and the phase velocity(setting is 500KHz...
