Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I am currently trying to run this ble_secure_bootloader . I am using SES V5.68 with the nRF52840 SoC and I am using nRF5 SDK version 14.2.0. I have also adjusted...
Hi Team,
I want to know the time with time resolution milliseconds for initialization time of nrf52840 chips and nrf52840 DK with external supply model?
KInd regards,...
Hi,
The below code I believe is in error. The below write operation overwrites the LIO2, LIO3, WIPWAIT, and WREN settings in the CINSTRCONF register by only writing the...
First off, It's great you guys are setting a high pace with development and improving the SDK but I and I think many other people would like it if you change a full version...
Hi!
I am currently working on this sample with an nrf52840 board and a nrf52832 board:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/peripheral...
Hi All!
Hope you are doing well! I am using nrf52840 and nrf58233. Is there any example available for both transmitter and receiver for connectable coded PHY beacons?...
I am trying to determine the best way to debounce 7 digital inputs with 2 bounce times ranging between 50 ms to 2 seconds. I thought of using the GPIOTE but that seems to...
Hi All,
I asked this question before but I accidentally pressed close.
The engineer told me that f or nRF5 SDK ( I assume as you said Segger), you can send 10 byte long...
I'm working with the project based on nrf52833 and SDK 17. I've noticed that when there are no devices on I2C bus, the application stucks on nrf_drv_twi_tx function, and the...
Hi , I'm using nrf5340 and nrf connect sdk 1.5.1 , recently I found out when sending large amount of data with low RSSI through bt_gatt_notify_cb the system would enter some...
Hi. I am using the Nrf52DK to program our custom Nrf52810 based board for DFU . We use the: nrf5sdk v17.0.2 with softdevice s112. along with the pca10040e_s112_ble example...
Hi,
I do not understand why assertion is not thrown when nrfx_saadc_init method is called with NULL event handler. For example:
err_code = nrf_drv_saadc_init(&default_config...
Hi,
We are evaluating the effect of mobility for applications running on nRF9160 in the LTE-M mode. The evaluation is done in a private research and testing network. At...
I have just started learning the ble mesh basics.I have started to build code . I have to learn the mesh examples code in a detailed way . Can you please tell me where I have...
