Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi everyone, i am developing a system where i have 2 types of board, one board is a central&peripheral (lest name it BOARD1), and the other board is only a peripheral(lets...
Hello!
First of all, thank you for your support.
I'm starting to develop firmware for Nordic chips (I'm a complete newbie). I have been able to compile and download examples...
Hello everybody,
I'm trying to develop simple time synchronization system upon mesh time model, but after sending bt_mesh_time_cli_time_set, first of all my time_update_cb...
NRF52840, SDK, nrf5-sdk-17.
This could be a misunderstanding of how the dual bank update works, however I am finding that after an OTA, Bank0 contains the new fw image but...
I have an SPI sensor that benefits from having a precise clock source, and has a muxed pin that can have a clock source.
The peripheral states that this pin can handle frequencies...
Hi,
We have implemented the DFU Trigger Library on nRF52840 from nRF SDK 15.3 on Application FW. Application is flashed on the device along with Secure Bootloader using...
Hello Nordic team,
I come to you because I face a strange issue during developing a simple feature using PWM.
For a product, I need to make an LED blink smoothly 3 times...
I have a NRF52840 Devkit and also subsequent NRF52840 boards, and I was wondering if there's any WiFi support on them now. I'm aware that it's possible to use any WiFi module...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
I'm building a nrfmicro bluetooth keyboard controller which uses an ebyte E73-2G4M08S1C nrf52840. My programmer is cmsis dap link. Openocd verson is 0.11.0.
I built two...
Hi All,
I'm new to this wireless field. Is there any impact on power consumption based on RSSI level.
As I understand due bad RSSI there will be retries in communication...
I working on Asset_tracker_v2. After going hrough the code, I estimated the work flow to be as:
1. When either Passive or Active state is intialized, the Sample Timer is...
Hi there,
I am running into this error Update CTE params...failed (err -134) while running the direction_finding_connectionless_tx
The output logs are
can I get more...
Hello,
In the product specification for the npm1100 there is an optional battery monitoring circuit schematic on page 39. I'm having trouble understanding why there are...
