Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 Base source: C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\peripheral_hids_keyboard
I want to add UART implementation....
Hi everyone!!! I need help with our new version of HW after validating the previous one that works.
I read some similar posts related to the GPRETREG for HOLD a GPIO while...
Hello,
I'm currently using the nrf9160 for a university project and I'm having problems with connecting my custom PCB with nrf9160 to nRF Cloud using the asset-tracker-v2...
Hi Nordic,
We have a design where we'd like to share the 2.4 GHz antenna between WiFi and BLE.
Therefore, we need to power and configure the RF switch accordingly, before...
Hi,
currently I am using nRF52811 in one product with BLE functionality. Now I would like to use the same MCU in other product where BLE is not needed. In this case I would...
We are developing a product based on nRF52832 and we need to verify that in case of problems, the device will "fail gracefully". So we looked at implementing the ARM handlers...
I am using LSM6DSOX IMU sensor INT detection with NRF52-DK and have extra 400µA (PPK2 used) on my setup. After a few days of nightmares I finally found that this is related...
Hi,
I'm using nRF Connect SDK v1.9.0
We're working on firmware running on an nRF9160 with TF-M enabled. We need to link with a library to is built with hard-float, so...
Hi,
i want to read temperature sensor value inside the nrf soc on bl653 board. while checking there is a file inside ( \zephyr\drivers\sensor\nrf5) this path. how to configure...
Hi,
I am working on DFU-OTA example. am looking for example , which will help me to copy image from slot1 to slot0 without using scratch pad. it has to override the image...
Hello Team,
I am using the ble_app_hrs_rscs_relay example where NRF52 acts both as a central and peripheral. My question is that when I remove the heart sensor Polar H10...
Hi,
I am working on DFU-OTA sample as suggested in this link. https://devzone.nordicsemi.com/f/nordic-q-a/84766/sample-ncs-code-to-evaluate-dfu-ota-on-nrf52833 .
For nrf52833...
Hello,
I'm using a custom board and i actually have a problem that I never saw before : error 34 (0x22) GATT CONN LMP TIMEOUT.
I have send frames : I did my own custom...
Hello ! I would like to know if the nrf52840 is affected by the errata https://infocenter.nordicsemi.com/topic/errata_nRF52832_Rev2/ERR/nRF52832/Rev2/latest/anomaly_832_149...
I have a custom design with NRF9160. I try to use the debug output of the NRF9160 DK, but on the debug-out of the nrf91 DK it is not recognize (target Voltage is visible at...
