Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
Our customer needs CAT-M, CAT-NB, GPS RF test data
I see that devZone has less information about CAT-M, CAT-NB and GPS RF performance tests
1. Please provide GPS...
As requested I am posting a public question based on Nordic's request here:
https://www.linkedin.com/feed/update/urn%3Ali%3Aactivity%3A6911310498537869312/?commentUrn=urn...
Hi,
parameters A NRF_SDH_CLOCK_LF_RC_CTIV
parameters B NRF_SDH_CLOCK_LF_RC_TEMP_CTIV
1. The internal RC parameter should be configured as follows, but how are parameters...
If AT+CFUN=1 will not get modem connected/registered to a network, what retry algorithm does the nRF9160 implement? Is it something like exponential back-off algorithm?
I'm attempting to add NVS functionality to my code. Had a play around with the zephyr/samples/subsys/nvs example. It was working originally, and then when I started porting...
Hi!
For a project I need to sample an I2C sensor for a period of 1 min with 1 sec between samples with a nordic nrf52832. During this 1 min, a co-processor communicates...
I'm trying to build a custom board in VS Code to use with the nRF9160. I'm using a Thingy91, so I took the board file for that, and copied it into the project directory. ...
I need to test the SPI communication in my nRF9160DK. I had tried to run the spi_loopback but failed to create a project in segger studio. Are there any SPI tests available...
So I have taken a starting point of adding multiple characteristics in the same service using this tutorial:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth...
We're trying to use multiple nRF52833 devices with a single BLE Central (Android tablet) where the devices remain disconnected most of the time, and report back to the central...
Hi,
I've been upgrading a product we designed some years ago with the S110 softdevice on an nRF51822 to use S130 and nRF5x SDK version 12.3 so that we can use the more modern...
Is there any precompiled binaries available to transfer the Thingy:91 sensor readings via usb serial like( temp, humi, pressure, light, accel, gas, lat&lng), right now I'm...
Hello, been trying to get Mosquitto MQTT Bridge working on EC2 (where mosquitto is running). https://docs.nrfcloud.com/Guides/Messages/SetupMessageBridge/#message-bridge-setup...
Hi
Gazell libraries are provided in <SDK>/components/proprietary_rf/gzll/gcc/ and I have 2 questions about those a) I see 2 flavours: gzll_<$HW>_gcc.a and gzll_<$HW>_sd_resources_gcc...
