Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
The current PC release of nrfutil.exe, v6.1.2, gives 9 malicious warnings on VirusTotal , including warnings from a couple of the big anti-malware vendors.
I would suggest...
Hi all
I used to use bmi160 for my application with nRF52833 and I am upgrading to bmi270 with nRF52840.
I am struggling to make work the functionalities I used to have...
Hi,
I have an application where I want to send sensor data using advertisement message, and read this message by an iPhone. For test purpose, I am currently transmitting...
Hello,
So, I have a working BLE project on the nRF52840 Dongle and I developed and debugged everything on the DevKit, using Zephyr/nRF Connect for VS Code. From there, I...
Hello, I'm using nrf52832, my own custom board, the UART pins are 10 out, 9 in, no stop bit, no parity and no hardware flow control, baud rate 115200.
Ever so often, in...
Hi,
I'm using SDK17.0.2 example(ble_uart) on nRF52832.When I enabled SPIM to drive sensor,and send data, RTT Viewer logging SOFTDEVICE: INVALID MEMORY ACCESS.
BTW I have...
Hi! This might be non-coherent, I apologize in advance as my knowledge in RF is very limited.
We're developing a sort of 'TX-negotiation protocol' between our peripherals...
I keep receiving the email stating the following, even after having all the points taken care of :-
1. I am using a active / approved DevZone Account.
2. I am using the...
Background - found during testing with proprietry application derived from the 'light_ctrl' sample in nRF Connect SDK, with Time & Schedule Servers added, on an nRF52833DK...
Hi
I have integrated the example code for mesh dfu provided in the nrf mesh sdk5 in my main application . I have followed all the steps mentioned in this dfu guide. The...
Hi,
i have a question regarding the USART NUS error handler.
In my setup, two Nordic BLE Chips are communicating via the USART service.
One chip is acting as a central...
hello everyone,
i am using nrf52810 with my custom board which contains mpu6050 accelerometer and Gyro-meter so now i want to achieve connectable beacon like it should be...
Hi, I received nRF9160DK kit with a SIM. I want to test SIM registration on Vodafon Network , Data transfer to a server ? Is there any concerned sample available in SDK Connect...
Hell Respected Members.
Referring to my previous question https://devzone.nordicsemi.com/f/nordic-q-a/85221/retaining-rtc-time-after-resetting-nrf52840 . give me a reply...
Hello
I was considering using sim cards other than iBasis for the nrf9160. I was wondering if they could still be provisioned using nRF cloud, or if there was a different...
