Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
We have a mature product based on the STM32 ARM processor family running the uCOS OS and our development toolchain is IAR. The workflow has worked well in the past when...
Dear all,
I ran LPCOMP example from SDK16 on nRF52 DK and it works just fine.
But I've occurred some problem modifying reference voltage. I init the lpcomp the same...
Hi ,
I have my own custom nrf52832 pcb. I have 2 chips on my pcb.
I program my device with Nrf52 Dk.
When I program MCU 1. The program is uploaded successfully and i...
Hai
I'm using nrf52811 and sdk17.1.
I tried all peripheral examples But I can't set advertising data to more than 31 bytes.
If I increase the data size some parameters...
Hi , I am using ZEPHYR rtos , and using the internal bootloader and its working fine and there are two images but now my code size has increased and i can not store 2 images...
Hi
I want to use app_uart_put() to send an array which is over 4096 bytes.I try to change the value of UART_TX_BUF_SIZE to 10K bytes，then call the app_uart_put() to send...
Hey
what are the downsides of using the already burned-in Random Static Device Address compared to a Public Address?
My assumptions are as follows:
Pro
Con...
Hi,
I have been working on Zephyr for the past weeks and have been able to set multiple GPIOs, interrupts and RF functionnalities. But so far, I thought I could handle...
We'd like to use Thingy91 to measure temperature, but it looks like the thermometer (BME680 onboard) gets heat up, when Thingy91 is running for some time.
I placed the device...
Hi,
I'm supporting a customer who is planning to use T-Mobile as their carrier. One of T-Mobile's questions is:
APN requirements: Private APN requires an IPSec VPN or...
Hi,
The spi_config structure zephyr provides is as below: Wherein cs is initialized to the chip select pin. In my project I have a requirement to handle 2 slaves which...
There is a bug in the sample/nrf9160/at_monitor, namely to do with +CEREG unsolicited notification handler called "cereg_mon". "cereg_mon" expects 0-2 +CEREG status code,...
I'm trying to replace a RS232 cable with a BLE bridge with the Nordic Uart Service.
One nRF52832 configured as central (app_uart_example_central) and an other one as peripheral...
Hello,
We are working on a product that contains nRF51822. The product sends continuous data (2 bytes) via NUS service to the mobile app at a frequency of 200ms.
When...
