I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Morning Everyone,
We use raspberry pis as part of our test equipment. The final stage of our CI/CD pipeline downloads the build dfu packages to a Pi and then does an OTA...
Hi,
I try to run SDK17.1 examples/dfu/secure_bootloader/pca10040_uart_debug.
Only UART example does not have softdevice.
I build and run that example on SES on M1...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Hi Sir/Miss,
I encounter a problem which is in programmer software.
When I open software and connect to nRF52840 DK. Right flash size window will display some animation...
Hi,
Is it possible to send data on Connected mode and in parallel also send the periodic data ?
I tried to implement that but it fails to send in data on Connected...
Hi,
We setup a mesh network with 26 sensor devices, configured these 26 devices into one group. From the mesh gateway device, it sends group message to these 26 devices...
Hi there,
I'm currently using SDK 17.1.0 with the NRF52832 Development Board. This is pretty new to me, but the examples helped me get an application going pretty quickly...
I'm using a nrf52840dongle board with the prj_no_dfu.conf configuration with the following additions:
CONFIG_BOARD_HAS_NRF5_BOOTLOADER=n CONFIG_CHIP_LIB_SHELL=y CONFIG_LOG...
Dear Nordic Engineers
I install nrf command line 10.1.6.0 in my office PC.There was a problem after the installation complate.
I input "nrfjprog" in powerShell ,it's normal...
Hello,
we have a remote control with 7 buttons.
Every button shall wakeup the device from deep sleep.
Beside i will have an interrupt on Button 6 and 7.
So the problem...
I am using nrfconnect 1.5.1 (zephyr/command line) with modem firmware 1.2.3 and believe I have found a fairly serious bug/behavior in the UDP API. It is pretty easy "crash...
Hi,
I looked at some of the questions on the forum and they didn't give me good advice. Currently all I can do is nrf52832 Security 1 Level 4 and nrf52833 Security 1 Level...
In the nRF5340 product specification version 1.2, I see an internal bandgap reference error range of -1.8/+0.5%.
In the nRF5340 product specification version 1.2, I see...
