Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I have a few questions about operation around the nRF9160.
I uploaded a minimal program on the nRF9160-DK card to obtain low consumption.
I get 600uA on average. In...
Hi,
I have implemented the USBD CDC ACM driver into my firmware. What stands out is the latency as soon as the event
APP_USBD_CDC_ACM_USER_EVT_PORT_OPEN triggers, my terminal...
hello. im having issues using ble uart, im planning on connecting my phone to nordic by bluetooth and to pc by usb, the problem that I have is when I use a usb port terminal...
Hi,
We are going through the errata file (nRF52840 rev 2) and wonder how to link anomaly (chip level) with nRF Connect SDK release (RTOS level)...
Where to find the...
Hi!
I am trying to interface LIS3DH module ( https://www.adafruit.com/product/2809 ) with nRF52 DK, SDK 11, via i2c/spi. I tested on Arduino UNO & it gave x,y,z values....
Hello, industry. Two questions for you:
1. To test fault-tolerance of our BLE scanning device we need to generate and advertise from another BLE device custom faulty ...
Hi,
We want to know more about BLE mesh OTA update in Nordic Connect SDK V1.8
Can you please share detail implementation on Firmware Over the air update in NCS 1.8 ...
Hi,
With the latest SDK v 14.2 is it possible to do OTA updates to nRF52 from OSX/Windows/Linux without the use of additional DK? I understand that for iOS and Android...
This might not be the optimal forum for this question, but I'm not sure where else to post it. I have a (I think) very simple question about configuring Zephyr.
I have a...
Hi!
Currently working on a firmware upgrade of nRF91 ns(non-secure) board and build a smp_svr demo from ncs samples found on ncs\v1.7.0\zephyr\samples\subsys\mgmt\mcumgr...
SDK: NCS 1.7.1.
Based on: Peripheral UART example
Central: nRF Dongle
Peripheral: nRF52832
Hi,
I am running into an issue using the "Just Works" pairing method when...
Hi, I was wondering if there is any way to advertise connectable, but non-scannable advertisements.
My device does not have a scan response, but I still see a lot of scan...
Hello,
There is a small problem that I don't know how to solve. I tried looking for it but to no avail. Essentially, my device which runs on NCS v1.7.0 will stop advertising...
Hello,
I am currently trying to record audio using a PDM microphone on the nrf52840 using the nordic PDM library. I have configured the PDM with the default settings, enabled...
nRF52810 SDKs and SoftDevices compatibility matrix does not list nRF52810 SoC revision 2 in the list of compatible SoC revisions for nRF5 SDK. Revision 2 is listed only in...
