Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I just installed the nRF toolchain and Programmer application to start using my nRF52840-DK eval board. I have the board connected through J2 to my computer and I can flash...
hello Nordic
i am using nrf52840 with zephyr ncs
unfortunatly i used this command "pamac install downgrade" at one point
since then i can not use 'west flash --erase...
nRF5 SDK > nRF5 SDK v15.0.0 > User Guides > Developing for nRF52810 gives a list of things to do to adapt an nRF528 32 project to an nRF528 10 target.
But, looking at...
Long story short.
I am trying to merge DFU master code to feed a DFU.zip to the DFU receiver code already present in the secure bootloaders (but elevated successfully into...
I'm working with firmware and hardware that has previously worked properly. I recently migrated to S113 from S140, and changed the data format of what was being set in the...
I am trying to create my first Freestanding Application under NRF Connect, I have SDK version 1.8.0. As soon as I click on "Create Application" I got the error message " Application...
Hi,
I am looking for the sample code of Class B type LoRaWAN end node for Zephyr platform. I am using ncs 1.8.0. I am able to find sample for Class A end node at v1.8...
Hi All,
I recently got hold of some new iBasis Sims and I know that sim card numbers vary from 18-20 digits, where the last 2 digits are the CRC and an extra byte. Where...
Trying to build the OpenThread sample programs (coap_server and coap_client) and am running into some problems that I hope someone might recognize as an easy fix.
In the...
Hello all, This is my first project using Nordic chips and my first project using BT. A lot of firsts :)
I have made a custom board using nRF52820 chip. The board is 4 layer...
To the kind attention of Nordic support team,
I'm introducing dtm files to the project we are working on (fully developed using latest sdk17). We use in this project gzll_nrf52810_sd_resources_gcc...
Hello,
I want to integrate the LwM2M Carrier library for our firmware as we will be certifying our product from Verizon operator.
So, I am able to run the sample code...
I'd like to ask if I request to update the connection parameters via "sd_ble_gap_conn_param_update" and the center for any reason reject the connection parameter.
How can...
We are using the Nordic iOS and Android DFU libraries to perform firmware updates of a nRF52840.
When I attempt to use nrfutil pkg generate to create a DFU package that...
Hi,
I am developing an application with the lvgl driver. I was trying to make the example lvgl works, but I can not. I am using a 128 x 32 screen with a ssd1306 controller...
