I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
I want to know to which pin should i rely my AMPERMETER so i can measure the current consumption of the µC .
If you have other hardware solution to measure the...
Hello,
I am trying to flash a Sparkfun thing plus nrf9160 board but I am not able to for some reason.
This is what I am getting on the logs when trying to select the...
Hi all! I'm new to mesh bluetooth technology and I'm stuck with some bugs.
I am using the development boards nrf52dk and my goal is to create a network of about 6 nodes...
I am using nRF5 SDK version 17.1.0 and am seeing this line in file examples/ble_peripheral/ble_app_uart/pca10040/s132/ses/flash_placement.xml
<ProgramSection alignment=...
Hi, I am trying to transmit data via Bluetooth from two sensors at the same time to a dongle that will send the data to the computer via USB, I am able to connect the two...
Hello,
I'm doing some current measurements on both the Thingy91 and the nRF9160DK and I'm seeing some weird behaviours. My setup is as follows:
First measure on the nRF9160DK...
Hi dear reader
I've read several threads on this issue, but none of them could help resolve my problem.
I've an application which currently is only starting some advertising...
Hi
I am looking for an advise about selection of the optimal connection parameters. I am using couple of nrf52832 devices as the nus peripherial. As the central device I...
Dear colleagues,
I'd be very grateful for your help in the following challenge: I would need to change pins and/or i2c bus speed without recompilation of my code.
I can...
Hi,
I am following the NRF5 getting started guide. Unfotunately, I am falling down at the first hurdle. When copying the .hex to the JLINK storage, a fail.txt is generated...
i am using a custom board same as the https://devzone.nordicsemi.com/f/nordic-q-a/29195/nrf52810-custom-board
i edited pca10040e_s112.
it got stuck at sd_ble_gap_ppcp_set...
Battery free BLE solutions are exanpding (wiliot, nexite, atmosic etc). Is there a plan in Nordic to provide a low power chip that will support battery free (or at least ...
I am trying to use the MCP2515 SPI2CAN adapter with the nRF9160 DK.
I started by trying to get the Zephyr socket_can sample to work. My efforts are based on this thread...
Ever since the toolchain manager v1.0.0 came out in the nRF Connect software, I have been unable to download it. I keep getting this error:
Any ideas?
Thanks,
Jow...
